{"product_id":"afm-dfm-vcm-disabler-cadillac-ct6-2016-2018-afm-dfm-disabler","title":"Cadillac CT6 2016-2018 3.0L\/3.6L V6 AFM\/DFM Disabler","description":"\u003cp\u003eFor the 2016–2018 Cadillac CT6: an OBD-II plug-in module that stops the engine from switching into cylinder-deactivation mode. The engine stays on all cylinders during cruising and light throttle, where AFM would normally shut half of them down. Installation is plugging it in. Nothing is spliced, flashed or removed from the engine, and the factory system resumes as soon as the module is unplugged.\u003c\/p\u003e\u003ch2\u003eCovered applications\u003c\/h2\u003e\u003cp\u003eListed applications, each a 100% fitment match:\u003c\/p\u003e\u003cul\u003e\u003cli\u003e2016–2018 Cadillac CT6: 3.0L V6 \/ 3.6L V6\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eGM used several V6 families in these years. Before ordering, confirm from your RPO label or VIN that your engine is the one listed and that it is equipped with cylinder deactivation; if in doubt, send the VIN to support.\u003c\/p\u003e\u003ch2\u003eHow Active Fuel Management operates\u003c\/h2\u003e\u003cp\u003eCylinder deactivation shuts off fuel and valve operation on part of the engine at light load, then brings those cylinders back when you need power. The engine computer decides when to switch based on load, speed and other inputs. This module works through the OBD-II port to keep the computer from choosing the reduced mode.\u003c\/p\u003e\u003ch2\u003ePlug-in module vs. a mechanical AFM delete\u003c\/h2\u003e\u003cp\u003eA mechanical AFM delete swaps the deactivating lifters (and often the camshaft and lifter oil manifold) for non-AFM parts and requires a tune afterwards. A tune alone can switch AFM off in software. This module works through the OBD-II port instead, so the engine hardware and its calibration stay stock. That makes it the easiest option to reverse, and the right one only when the engine is mechanically healthy.\u003c\/p\u003e\u003ch2\u003ePractical notes\u003c\/h2\u003e\u003cp\u003eBecause it occupies the OBD-II port, unplug the module before connecting a scan tool, an insurance logger or an emissions-test probe, then plug it back in afterwards. Make sure it sits clear of your left knee and the pedals, and that the housing is fully seated in the port.\u003c\/p\u003e\u003ch2\u003eWhat changes when you drive\u003c\/h2\u003e\u003cp\u003eExpect steadier behavior at part throttle and no change at wide-open throttle. Towing and hill climbing were already mostly done on all cylinders, so the biggest change is during relaxed cruising. Average fuel economy may drop slightly depending on how much of your driving is light-load highway time.\u003c\/p\u003e\u003ch2\u003eWhat owners are after\u003c\/h2\u003e\u003cp\u003eA Cadillac CT6 with AFM switches modes many times on a typical drive. Some owners never notice; others feel it every time. If you are in the second group, or you tow and want steady behavior, keeping all cylinders active is the simplest answer. Fuel use at light cruise will usually rise a little, since that is where AFM saves fuel.\u003c\/p\u003e\u003ch2\u003eOil and maintenance\u003c\/h2\u003e\u003cp\u003eOil level and quality are worth watching on any AFM engine, because the deactivation hardware is hydraulic. Check the dipstick at fuel stops on high-mileage engines, follow GM's specified oil grade, and address oil-pressure warnings immediately. None of that changes with the module installed.\u003c\/p\u003e\u003ch2\u003eBefore installing\u003c\/h2\u003e\u003cp\u003eThis module prevents mode switching. It does not repair anything. If the engine already has a ticking lifter, misfire codes, low oil pressure or high oil consumption, have it diagnosed before relying on the module. Those symptoms need a mechanical repair, and keeping AFM off will not reverse damage that has already happened.\u003c\/p\u003e\u003ch2\u003eFitment check\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eYour model year, model and engine match a row in the table (2016–2018 Cadillac CT6).\u003c\/li\u003e\n\u003cli\u003eThe quickest checks are the 8th digit of your VIN, which identifies the engine, and the RPO list on the Service Parts Identification label (glovebox or trunk on most pre-2018 GM models, QR code on the driver-door pillar label from 2018).\u003c\/li\u003e\n\u003cli\u003eThe engine runs cleanly with no stored misfire or AFM codes.\u003c\/li\u003e\n\u003cli\u003eEngine swaps, custom tunes and replaced ECUs need a fitment check from support before ordering.\u003c\/li\u003e\n\u003cli\u003eQuestions: support@automotivebypass.com with your VIN.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eYear-by-year fitment\u003c\/h2\u003e\u003cp\u003eEach model year from the fitment data, with the AFM engine codes GM used for that year and displacement:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine\u003c\/th\u003e\n\u003cth\u003eAFM codes\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2016\u003c\/td\u003e\n\u003ctd\u003eCadillac\u003c\/td\u003e\n\u003ctd\u003eCT6\u003c\/td\u003e\n\u003ctd\u003e3.0L V6 \/ 3.6L V6\u003c\/td\u003e\n\u003ctd\u003eConfirm by VIN\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2017\u003c\/td\u003e\n\u003ctd\u003eCadillac\u003c\/td\u003e\n\u003ctd\u003eCT6\u003c\/td\u003e\n\u003ctd\u003e3.0L V6 \/ 3.6L V6\u003c\/td\u003e\n\u003ctd\u003eConfirm by VIN\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2018\u003c\/td\u003e\n\u003ctd\u003eCadillac\u003c\/td\u003e\n\u003ctd\u003eCT6\u003c\/td\u003e\n\u003ctd\u003e3.0L V6 \/ 3.6L V6\u003c\/td\u003e\n\u003ctd\u003eConfirm by VIN\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eAfter-install checks\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eWarning light appears:\u003c\/strong\u003e Remove the module, scan for codes and email support with the code and VIN.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMode changes still felt:\u003c\/strong\u003e Re-seat the module and confirm your engine code is on the AFM list for this listing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eShop cannot reach the diagnostic port:\u003c\/strong\u003e Unplug the module for the visit and refit it afterwards.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eLifter noise or misfire codes:\u003c\/strong\u003e These point to existing engine faults that need diagnosis and repair.\u003c\/p\u003e\u003ch2\u003eQuick definitions\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eAFM:\u003c\/strong\u003e Active Fuel Management, GM's cylinder deactivation system on the engines covered here.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOBD-II port:\u003c\/strong\u003e The standard diagnostic connector under the dash on every US vehicle since 1996.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSPID label:\u003c\/strong\u003e Service Parts Identification label listing the RPO codes on pre-2018 GM vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRPO code:\u003c\/strong\u003e GM's three-character option code; engine codes begin with L.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eVIN 8th digit:\u003c\/strong\u003e The VIN character that identifies the engine.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoD:\u003c\/strong\u003e Displacement on Demand, the original name for AFM.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDFM:\u003c\/strong\u003e Dynamic Fuel Management, the system on 2019-on L84 and L87 engines that can deactivate cylinders individually.\u003c\/p\u003e\u003ch2\u003eFrom Displacement on Demand to DFM\u003c\/h2\u003e\u003cp\u003eGM first sold cylinder deactivation in 1981 with the Cadillac V8-6-4. The modern system was announced in 2003 as Displacement on Demand and reached production on the 2005 Chevrolet TrailBlazer EXT and GMC Envoy XL and XUV with the 5.3L V8, followed by the 5.3L LS4 in the Impala SS, Monte Carlo SS and Pontiac Grand Prix GXP. Renamed Active Fuel Management, it spread across GM's Gen IV and EcoTec3 truck engines. For the 2019 Silverado, GM introduced Dynamic Fuel Management, based on Tula Technology's Dynamic Skip Fire, which can deactivate cylinders individually.\u003c\/p\u003e\u003ch2\u003eWhat is inside an AFM engine\u003c\/h2\u003e\u003cp\u003eAFM uses oil pressure as its control signal. A solenoid valve assembly under the intake manifold, in the valley cover, routes oil to collapsible lifters on the deactivating cylinders. Aerated or wrong-viscosity oil slows that signal. Keeping AFM off removes the switching, but every lifter still relies on the oiling system, so stick to the specified oil and intervals.\u003c\/p\u003e\u003ch2\u003eInstall prep checklist\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClear up any warning lights first: the module is for a healthy engine.\u003c\/li\u003e\n\u003cli\u003eConfirm oil level and grade.\u003c\/li\u003e\n\u003cli\u003eTurn everything off.\u003c\/li\u003e\n\u003cli\u003ePlug the module into the OBD-II port.\u003c\/li\u003e\n\u003cli\u003eCheck it is fully seated and cannot be kicked loose.\u003c\/li\u003e\n\u003cli\u003eStart the engine.\u003c\/li\u003e\n\u003cli\u003eCruise lightly on a level road to confirm all cylinders stay active.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eGM 3.6L V6 engines and AFM\u003c\/h2\u003e\u003cp\u003eGM built several 3.6L V6 versions, and only some have AFM. The LGX (2016-on Camaro) and the LGZ (2017-on Colorado and Canyon) both use direct injection, variable valve timing and Active Fuel Management, running on four cylinders at light load (cylinders 2 and 5 are shut down on the LGX). The LFX, used in the 2015–2016 Colorado and Canyon, and the LFY in the 2018 Traverse and Enclave do not have AFM. Your RPO code settles it.\u003c\/p\u003e\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\u003ch3\u003eWhich Cadillac CT6 years and engines does it fit?\u003c\/h3\u003e\u003cp\u003eThe fitment table lists Cadillac CT6 2016–2018 with 3.0L V6, 3.6L V6. Match your exact year and engine to a row before ordering.\u003c\/p\u003e\u003ch3\u003eDoes it plug into the OBD-II port on the Cadillac CT6?\u003c\/h3\u003e\u003cp\u003eYes. It plugs into the OBD-II port under the dash. There is no wiring or splicing.\u003c\/p\u003e\u003ch3\u003eDo I need to remove it for an emissions test or scan tool?\u003c\/h3\u003e\u003cp\u003eYes. It uses the diagnostic port, so unplug it while the port is needed and plug it back in afterwards.\u003c\/p\u003e\u003ch3\u003eCan I go back to factory AFM?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and the factory cylinder-deactivation strategy works again.\u003c\/p\u003e\u003ch3\u003eWill it add horsepower?\u003c\/h3\u003e\u003cp\u003eNo. It keeps all cylinders active; it does not change the engine tune.\u003c\/p\u003e\u003ch3\u003eWill it fix lifter noise or misfires?\u003c\/h3\u003e\u003cp\u003eNo. Those are mechanical or electrical faults that need their own diagnosis and repair.\u003c\/p\u003e\u003ch3\u003eHow much fuel does AFM save?\u003c\/h3\u003e\u003cp\u003eEPA-test estimates published for GM's system are about 5.5–7.5%, with the benefit coming from light-load cruising. Keeping all cylinders active gives up part of that, depending on how you drive.\u003c\/p\u003e\u003ch3\u003eIs a tune or ECU reflash required?\u003c\/h3\u003e\u003cp\u003eNo. The module plugs into the OBD-II port and does not rewrite the engine computer's software.\u003c\/p\u003e\u003ch3\u003eHow do I tell which engine my Cadillac CT6 has?\u003c\/h3\u003e\u003cp\u003eCheck the 8th digit of the VIN or the RPO codes on the Service Parts Identification label (QR code on the door-pillar label on 2018 and newer GM models).\u003c\/p\u003e\u003ch3\u003eDo I need it if my engine already has an AFM delete?\u003c\/h3\u003e\u003cp\u003eNo. An engine with the AFM hardware removed and a matching tune no longer deactivates cylinders, so the module has nothing to manage.\u003c\/p\u003e\u003ch3\u003eDoes it change anything when towing?\u003c\/h3\u003e\u003cp\u003eUnder heavy load, such as towing up a grade, AFM already keeps all cylinders running. The difference shows up during lighter cruising between climbs, where the engine no longer drops cylinders.\u003c\/p\u003e\u003ch3\u003eDoes it work on 2019 and newer trucks with Dynamic Fuel Management?\u003c\/h3\u003e\u003cp\u003eOnly the vehicles and engines in this listing's fitment table are covered. DFM on the 2019-on Silverado 1500 and Sierra 1500 (5.3L L84, 6.2L L87) is a different system, so do not assume coverage outside the table.\u003c\/p\u003e\u003ch2\u003eShipping, returns and warranty\u003c\/h2\u003e\u003cp\u003eFree standard shipping covers the contiguous US, with dispatch in 1–2 business days and 3–4 days on the road after that. You have 45 days to request a return (pre-approval required, 20% restocking fee, buyer-paid return shipping). The module is backed by a 3-year limited warranty. For order or fitment questions, write to support@automotivebypass.com between 9 and 5 Pacific, Monday through Friday.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493785153908,"sku":"RC-AFM-DFM-01-26","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/RC-AFM-DFM-01-26-1.jpg?v=1793172438","url":"https:\/\/automotivebypass.com\/products\/afm-dfm-vcm-disabler-cadillac-ct6-2016-2018-afm-dfm-disabler","provider":"Automotivebypass","version":"1.0","type":"link"}