{"product_id":"afm-dfm-vcm-disabler-cadillac-sts-2005-2007-afm-dfm-disabler","title":"Cadillac STS 2005-2007 3.6L V6 AFM\/DFM Disabler","description":"\u003cp\u003eA plug-in cylinder-deactivation disabler for the 2005–2007 Cadillac STS. It goes into the OBD-II diagnostic port and keeps the factory Active Fuel Management system from engaging, so the engine runs on every cylinder all the time. No tools, no wiring and no reflash of the engine computer. Unplug it and AFM works again as it did from the factory.\u003c\/p\u003e\u003ch2\u003eFitment by year and engine\u003c\/h2\u003e\u003cp\u003eEach row below is listed as a 100% fitment match:\u003c\/p\u003e\u003cul\u003e\u003cli\u003e2005–2007 Cadillac STS: 3.6L V6\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eConfirm that your exact engine is the one in the table and that it uses cylinder deactivation. The RPO label and the VIN engine digit are the reliable ways to check, and support can confirm from a VIN.\u003c\/p\u003e\u003ch2\u003eWhat AFM does on these engines\u003c\/h2\u003e\u003cp\u003eGM's cylinder deactivation saves fuel by running the engine on fewer cylinders during light-load cruising. The switch is controlled by the engine computer. The module talks to the vehicle through the OBD-II port and keeps that reduced-cylinder mode from being selected, so all cylinders stay active.\u003c\/p\u003e\u003ch2\u003eReasons to keep all cylinders running\u003c\/h2\u003e\u003cp\u003eThe usual complaints are a drone or shudder in reduced-cylinder mode, a slight hesitation when the engine switches back, and a general wish to keep the valvetrain doing the same thing all the time. With the module installed, the engine stays in full-cylinder mode, so those transitions stop. Expect light-load fuel economy to be closer to an engine without AFM.\u003c\/p\u003e\u003ch2\u003eEngine care\u003c\/h2\u003e\u003cp\u003eDisabling cylinder deactivation does not replace normal maintenance. Use the oil grade and change interval GM lists for your engine, watch the oil level between changes, and repair leaks promptly. The valvetrain on these engines depends on clean oil at proper pressure in every mode.\u003c\/p\u003e\u003ch2\u003eScan tools and inspections\u003c\/h2\u003e\u003cp\u003eThe module uses the OBD-II port, so it has to come out whenever a technician or an inspection station needs the port. Plugging it back in restores the all-cylinder mode. Route it so the driver cannot kick it loose.\u003c\/p\u003e\u003ch2\u003eBefore installing\u003c\/h2\u003e\u003cp\u003eThis module prevents mode switching. It does not repair anything. If the engine already has a ticking lifter, misfire codes, low oil pressure or high oil consumption, have it diagnosed before relying on the module. Those symptoms need a mechanical repair, and keeping AFM off will not reverse damage that has already happened.\u003c\/p\u003e\u003ch2\u003eOther ways owners disable AFM\u003c\/h2\u003e\u003cp\u003eThere are three common ways to stop cylinder deactivation on GM engines: a plug-in module like this one, a custom tune that turns AFM off in the engine computer, or a mechanical delete that replaces the AFM lifters and related hardware and then needs a tune to match. The module is the only one of the three that needs no tools and no engine-computer changes, and it is the only one you can undo by unplugging it. It does not replace failed lifters; if hardware is already damaged, the repair comes first.\u003c\/p\u003e\u003ch2\u003eWhat to expect on the road\u003c\/h2\u003e\u003cp\u003eThe difference shows up in light-load driving: steady highway speeds, gentle acceleration and coasting down small grades. Those are the moments when AFM used to drop cylinders. With the module in, engine behavior there should feel the same as under heavier throttle. Full-throttle performance does not change, because AFM was never active at full throttle anyway.\u003c\/p\u003e\u003ch2\u003eFitment check\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eYour model year, model and engine match a row in the table (2005–2007 Cadillac STS).\u003c\/li\u003e\n\u003cli\u003eLook up the engine RPO code. Older GM vehicles print it on the Service Parts Identification sticker, often in the glovebox; 2018 and newer GM models carry it in a QR code on the driver-side B-pillar label. You can also read the 8th digit of the VIN, which is the engine code.\u003c\/li\u003e\n\u003cli\u003eNo check-engine light is on, and oil level and pressure are normal.\u003c\/li\u003e\n\u003cli\u003eIf the vehicle has an engine swap, an aftermarket tune or a replacement engine computer, contact support first.\u003c\/li\u003e\n\u003cli\u003eQuestions: support@automotivebypass.com with your VIN.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eYear-by-year fitment\u003c\/h2\u003e\u003cp\u003eOne row per year. The last column shows which AFM-equipped GM engine codes match that year and engine size:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine\u003c\/th\u003e\n\u003cth\u003eAFM codes\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2005\u003c\/td\u003e\n\u003ctd\u003eCadillac\u003c\/td\u003e\n\u003ctd\u003eSTS\u003c\/td\u003e\n\u003ctd\u003e3.6L V6\u003c\/td\u003e\n\u003ctd\u003eConfirm by VIN\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2006\u003c\/td\u003e\n\u003ctd\u003eCadillac\u003c\/td\u003e\n\u003ctd\u003eSTS\u003c\/td\u003e\n\u003ctd\u003e3.6L V6\u003c\/td\u003e\n\u003ctd\u003eConfirm by VIN\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2007\u003c\/td\u003e\n\u003ctd\u003eCadillac\u003c\/td\u003e\n\u003ctd\u003eSTS\u003c\/td\u003e\n\u003ctd\u003e3.6L V6\u003c\/td\u003e\n\u003ctd\u003eConfirm by VIN\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eFrom Displacement on Demand to DFM\u003c\/h2\u003e\u003cp\u003eGM first sold cylinder deactivation in 1981 with the Cadillac V8-6-4. The modern system was announced in 2003 as Displacement on Demand and reached production on the 2005 Chevrolet TrailBlazer EXT and GMC Envoy XL and XUV with the 5.3L V8, followed by the 5.3L LS4 in the Impala SS, Monte Carlo SS and Pontiac Grand Prix GXP. Renamed Active Fuel Management, it spread across GM's Gen IV and EcoTec3 truck engines. For the 2019 Silverado, GM introduced Dynamic Fuel Management, based on Tula Technology's Dynamic Skip Fire, which can deactivate cylinders individually.\u003c\/p\u003e\u003ch2\u003eThe V6 question\u003c\/h2\u003e\u003cp\u003eFor V6 applications, the engine code matters more than the displacement. AFM is part of the LGX (2016-on Camaro, which drops cylinders 2 and 5) and the LGZ (2017-on Colorado and Canyon). The LFX that preceded them, including in the 2015–2016 Colorado and Canyon, and the LFY in the 2018 Traverse and Enclave run on all six cylinders all the time and are not candidates for this module.\u003c\/p\u003e\u003ch2\u003eGlossary\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eSPID label:\u003c\/strong\u003e Service Parts Identification label listing the RPO codes on pre-2018 GM vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAFM:\u003c\/strong\u003e Active Fuel Management, GM's cylinder deactivation system on the engines covered here.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDFM:\u003c\/strong\u003e Dynamic Fuel Management, the system on 2019-on L84 and L87 engines that can deactivate cylinders individually.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eVIN 8th digit:\u003c\/strong\u003e The VIN character that identifies the engine.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoD:\u003c\/strong\u003e Displacement on Demand, the original name for AFM.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOBD-II port:\u003c\/strong\u003e The standard diagnostic connector under the dash on every US vehicle since 1996.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRPO code:\u003c\/strong\u003e GM's three-character option code; engine codes begin with L.\u003c\/p\u003e\u003ch2\u003eWhy oil matters on these engines\u003c\/h2\u003e\u003cp\u003eAn AFM engine has a solenoid valve assembly in the engine valley cover. Its solenoids send pressurized oil to special hydraulic roller lifters (supplied by Eaton and Delphi) on the deactivating cylinders, which then stop opening the valves. Because the system runs on oil pressure, oil quality matters: worn-out anti-foam additives, the wrong viscosity or overdue changes can delay the oil signal and upset the switching. The module stops the switching; the oil system still needs proper care.\u003c\/p\u003e\u003ch2\u003eTroubleshooting\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eA light comes on:\u003c\/strong\u003e Pull the module, read the code, and send it with your VIN to support.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eStill dropping cylinders:\u003c\/strong\u003e Check the module is pushed fully into the port and that your engine is AFM-equipped.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNeed the port for diagnostics:\u003c\/strong\u003e Remove the module first.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNoise or misfire persists:\u003c\/strong\u003e Have the engine inspected; the module only stops cylinder deactivation.\u003c\/p\u003e\u003ch2\u003eInstall prep checklist\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClear up any warning lights first: the module is for a healthy engine.\u003c\/li\u003e\n\u003cli\u003eConfirm oil level and grade.\u003c\/li\u003e\n\u003cli\u003eTurn everything off.\u003c\/li\u003e\n\u003cli\u003ePlug the module into the OBD-II port.\u003c\/li\u003e\n\u003cli\u003eCheck it is fully seated and cannot be kicked loose.\u003c\/li\u003e\n\u003cli\u003eStart the engine.\u003c\/li\u003e\n\u003cli\u003eCruise lightly on a level road to confirm all cylinders stay active.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\u003ch3\u003eWhich Cadillac STS years and engines does it fit?\u003c\/h3\u003e\u003cp\u003eThe fitment table lists Cadillac STS 2005–2007 with 3.6L V6. Match your exact year and engine to a row before ordering.\u003c\/p\u003e\u003ch3\u003eWill it fix lifter noise or misfires?\u003c\/h3\u003e\u003cp\u003eNo. Those are mechanical or electrical faults that need their own diagnosis and repair.\u003c\/p\u003e\u003ch3\u003eDo I need to remove it for an emissions test or scan tool?\u003c\/h3\u003e\u003cp\u003eYes. It uses the diagnostic port, so unplug it while the port is needed and plug it back in afterwards.\u003c\/p\u003e\u003ch3\u003eDoes it plug into the OBD-II port on the Cadillac STS?\u003c\/h3\u003e\u003cp\u003eYes. It plugs into the OBD-II port under the dash. There is no wiring or splicing.\u003c\/p\u003e\u003ch3\u003eHow do I tell which engine my Cadillac STS has?\u003c\/h3\u003e\u003cp\u003eCheck the 8th digit of the VIN or the RPO codes on the Service Parts Identification label (QR code on the door-pillar label on 2018 and newer GM models).\u003c\/p\u003e\u003ch3\u003eDoes it change anything when towing?\u003c\/h3\u003e\u003cp\u003eUnder heavy load, such as towing up a grade, AFM already keeps all cylinders running. The difference shows up during lighter cruising between climbs, where the engine no longer drops cylinders.\u003c\/p\u003e\u003ch3\u003eDoes it work on 2019 and newer trucks with Dynamic Fuel Management?\u003c\/h3\u003e\u003cp\u003eOnly the vehicles and engines in this listing's fitment table are covered. DFM on the 2019-on Silverado 1500 and Sierra 1500 (5.3L L84, 6.2L L87) is a different system, so do not assume coverage outside the table.\u003c\/p\u003e\u003ch3\u003eHow much fuel does AFM save?\u003c\/h3\u003e\u003cp\u003eEPA-test estimates published for GM's system are about 5.5–7.5%, with the benefit coming from light-load cruising. Keeping all cylinders active gives up part of that, depending on how you drive.\u003c\/p\u003e\u003ch3\u003eIs a tune or ECU reflash required?\u003c\/h3\u003e\u003cp\u003eNo. The module plugs into the OBD-II port and does not rewrite the engine computer's software.\u003c\/p\u003e\u003ch3\u003eCan I go back to factory AFM?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and the factory cylinder-deactivation strategy works again.\u003c\/p\u003e\u003ch3\u003eDo I need it if my engine already has an AFM delete?\u003c\/h3\u003e\u003cp\u003eNo. An engine with the AFM hardware removed and a matching tune no longer deactivates cylinders, so the module has nothing to manage.\u003c\/p\u003e\u003ch3\u003eWill it add horsepower?\u003c\/h3\u003e\u003cp\u003eNo. It keeps all cylinders active; it does not change the engine tune.\u003c\/p\u003e\u003ch2\u003eOrdering details\u003c\/h2\u003e\u003cp\u003eFree standard shipping covers the contiguous US, with dispatch in 1–2 business days and 3–4 days on the road after that. You have 45 days to request a return (pre-approval required, 20% restocking fee, buyer-paid return shipping). The module is backed by a 3-year limited warranty. For order or fitment questions, write to support@automotivebypass.com between 9 and 5 Pacific, Monday through Friday.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493785842036,"sku":"RC-AFM-DFM-01-33","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/RC-AFM-DFM-01-33-1.jpg?v=1793172507","url":"https:\/\/automotivebypass.com\/products\/afm-dfm-vcm-disabler-cadillac-sts-2005-2007-afm-dfm-disabler","provider":"Automotivebypass","version":"1.0","type":"link"}