{"product_id":"auto-start-stop-eliminator-2016-2018-honda-pilot-auto-start-stop-eliminator","title":"2016-2018 Honda Pilot Auto Start Stop Eliminator","description":"\u003cp\u003eIf your Honda Pilot turns Auto Idle Stop back on every time you start it, this inline memory harness solves that one problem: it remembers the last setting and restores it at the next ignition cycle. Coverage is the 2016–2018 Honda Pilot. It plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced.\u003c\/p\u003e\u003cp\u003eYou can still use the original button at any time. Whatever you select last is what the module repeats on the next start. Take the module out and the vehicle behaves exactly as it did from the factory.\u003c\/p\u003e\u003ch2\u003eVehicles and years covered\u003c\/h2\u003e\u003cp\u003eEvery row below is listed as a 100% fitment match for this part:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eHonda Pilot: 2016–2018\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eThe listing is written around the third-generation (2016-2022) Pilot. The table does not separate trims; what matters is that the vehicle has factory stop-start and the connector shown in the photos.\u003c\/p\u003e\u003ch2\u003eHow factory stop-start works on the Honda Pilot\u003c\/h2\u003e\u003cp\u003eAuto Idle Stop is designed to default to on. The off switch (usually marked with an \"A\" inside a circular arrow) cancels it for the current drive. At the next start the system is armed again. That reset is intentional on the manufacturer's side, and it is the only behavior this module changes.\u003c\/p\u003e\u003ch2\u003eConditions the factory system checks\u003c\/h2\u003e\u003cp\u003eEven with Auto Idle Stop enabled, the engine control logic only stops the engine when conditions allow it. Typical blockers are a low battery state of charge, an engine that has not reached operating temperature, heavy heating or A\/C demand, steering input, an open door or unlatched seatbelt, and some drive modes. If the system never seems to stop the engine, one of these is usually the reason, and the module does not change that logic.\u003c\/p\u003e\u003ch2\u003eScope of the module\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLeaves no permanent change after removal.\u003c\/li\u003e\n\u003cli\u003eLets you re-enable the system with the factory button at any time.\u003c\/li\u003e\n\u003cli\u003eLeaves engine and transmission software untouched.\u003c\/li\u003e\n\u003cli\u003eHolds the stop-start button state between drives.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eBattery notes for stop-start vehicles\u003c\/h2\u003e\u003cp\u003eThe module draws its power from the vehicle and does not change charging behavior. If your Honda Pilot sits for long periods, the same rules apply as without it: a maintainer helps, and a battery that tests weak should be replaced with the type specified for stop-start vehicles (usually AGM or EFB).\u003c\/p\u003e\u003ch2\u003eDiagnostics first\u003c\/h2\u003e\u003cp\u003eIf the setting is not remembered, check that the module was installed with the ignition off and that the connector clicked into place. Then press the factory button once, switch the vehicle off, close the doors, give the electronics time to shut down, and start again. If it still resets, contact support with the year, trim and a photo of the connector.\u003c\/p\u003e\u003ch2\u003eDay-to-day use\u003c\/h2\u003e\u003cp\u003ePressing the same button on every drive is what wears on owners. People who tow, plow, idle in pickup lines, creep through heavy traffic or simply want the engine running at a light end up making the same press dozens of times a week. On the Honda Pilot, the module turns that into a one-time choice you can still change whenever you want.\u003c\/p\u003e\u003ch2\u003eConnecting it\u003c\/h2\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced. Work with the ignition off. Seat each connector until its lock engages, then secure the module with the supplied ties or tape so it cannot rattle or touch pedals, steering parts or anything hot. Start the vehicle, press the stop-start button once, then restart to confirm the choice is held.\u003c\/p\u003e\u003ch2\u003eFitment check\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eModel year and model match a row in the table above (2016–2018 Honda Pilot).\u003c\/li\u003e\n\u003cli\u003eYour Honda Pilot has the factory stop-start button. Base trims or engines without stop-start have nothing for the module to remember.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket remote start, alarm or gateway bypass is wired into the same circuit. If one is, email support before ordering.\u003c\/li\u003e\n\u003cli\u003eThe battery and charging system test good and no warning lights are on.\u003c\/li\u003e\n\u003cli\u003eThe connector at your install point matches the one in the product photos.\u003c\/li\u003e\n\u003cli\u003eIf you are unsure, send your VIN to support@automotivebypass.com and we will confirm fitment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eYear-by-year fitment\u003c\/h2\u003e\u003cp\u003eEach model year in the fitment data, listed separately:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2016\u003c\/td\u003e\n\u003ctd\u003eHonda\u003c\/td\u003e\n\u003ctd\u003ePilot\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2017\u003c\/td\u003e\n\u003ctd\u003eHonda\u003c\/td\u003e\n\u003ctd\u003ePilot\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2018\u003c\/td\u003e\n\u003ctd\u003eHonda\u003c\/td\u003e\n\u003ctd\u003ePilot\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eQuick definitions\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eKey cycle:\u003c\/strong\u003e One switch-off and restart of the vehicle. Factory stop-start resets at each key cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNon-latching:\u003c\/strong\u003e A setting that does not stay where the driver left it after a restart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAGM \/ EFB battery:\u003c\/strong\u003e Battery types designed for the frequent cycling of stop-start vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAuto Idle Stop:\u003c\/strong\u003e Honda's name for the automatic engine stop-start feature on the Honda Pilot.\u003c\/p\u003e\u003ch2\u003eWhat sits behind the system\u003c\/h2\u003e\u003cp\u003eTo cope with repeated restarts, stop-start vehicles normally carry an AGM or EFB battery and a heavier-duty starter, and the system watches battery charge closely. If the battery is weak, the vehicle will skip automatic stops on its own. The module leaves this hardware and its monitoring alone. Use the factory battery type when replacing it, and check the owner's manual for any battery reset step after replacement.\u003c\/p\u003e\u003ch2\u003eThe reason the button has to be pressed every trip\u003c\/h2\u003e\u003cp\u003eCar makers have a clear reason to make stop-start non-latching. For EPA ratings, a system that always re-enables itself is counted as on, while one that can stay off is tested on and off and the results averaged. The lower average is something no manufacturer wants on a window sticker, so the default returns at every key cycle.\u003c\/p\u003e\u003ch2\u003eInstall prep checklist\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eIgnition off, transmission in Park, fob outside the cabin.\u003c\/li\u003e\n\u003cli\u003eInstructions for your exact model at hand.\u003c\/li\u003e\n\u003cli\u003eConnector location confirmed against the photos before any panel comes off.\u003c\/li\u003e\n\u003cli\u003eA plastic pry tool for clips, if the connector sits behind trim.\u003c\/li\u003e\n\u003cli\u003eBoth connector locks fully engaged after fitting.\u003c\/li\u003e\n\u003cli\u003eModule and lead fixed in place, clear of pedals, steering and heat.\u003c\/li\u003e\n\u003cli\u003eTest: choose your Auto Idle Stop setting, turn the vehicle off, restart and check the indicator.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon questions after fitting\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eSetting not remembered:\u003c\/strong\u003e Check that both connectors are fully latched, then set Auto Idle Stop the way you want it, switch the vehicle fully off and restart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eStop-start indicator flashes or shows unavailable:\u003c\/strong\u003e The vehicle is reporting a condition such as low battery charge, high climate demand or a cold engine. That comes from the factory logic, not the module.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWarning message after fitting:\u003c\/strong\u003e Unplug the module, reconnect the factory connector and see whether the message clears. Contact support with the VIN and a photo of the connector.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eEngine still stops at lights:\u003c\/strong\u003e That means Auto Idle Stop was left on before shutdown. Press the button once to switch it off; the module remembers that choice from the next start.\u003c\/p\u003e\u003ch2\u003eFAQ\u003c\/h2\u003e\u003ch3\u003eWill it fix a \"stop-start unavailable\" message?\u003c\/h3\u003e\u003cp\u003eNo. That message usually points to the battery or a sensor. Diagnose and repair that first.\u003c\/p\u003e\u003ch3\u003eDoes it change engine power or fuel trims?\u003c\/h3\u003e\u003cp\u003eNo. It does not reprogram the engine or transmission computers. It only stores the stop-start button state.\u003c\/p\u003e\u003ch3\u003eWhich Honda Pilot years does this fit?\u003c\/h3\u003e\u003cp\u003eThe listed range is 2016–2018. Check the fitment table on this page against your exact model year.\u003c\/p\u003e\u003ch3\u003eWill Auto Idle Stop come back on when I restart my Honda Pilot?\u003c\/h3\u003e\u003cp\u003eNot if you turned it off before shutting down. The module repeats your last selection at the next start. If you leave it on, it stays on.\u003c\/p\u003e\u003ch3\u003eWhy does my Honda Pilot sometimes not auto-stop even when the system is on?\u003c\/h3\u003e\u003cp\u003eThe factory logic checks battery charge, engine temperature, climate load and other inputs. If any are outside range it keeps the engine running. The module does not affect those checks.\u003c\/p\u003e\u003ch3\u003eDoes it change how the battery is charged?\u003c\/h3\u003e\u003cp\u003eNo. Charging is still managed by the vehicle. Stop-start vehicles normally use an AGM or EFB battery built for frequent restarts; replace it with the same type when it wears out.\u003c\/p\u003e\u003ch3\u003eWhat happens if I unplug it?\u003c\/h3\u003e\u003cp\u003eThe vehicle returns to the factory default, with Auto Idle Stop switched on at every start.\u003c\/p\u003e\u003ch3\u003eCan I remove it later?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and reconnect the factory connector; the vehicle returns to its stock default.\u003c\/p\u003e\u003ch3\u003eIs this the same part for every Honda?\u003c\/h3\u003e\u003cp\u003eNo. Connectors and the module that holds the stop-start state differ by platform, so this SKU is matched to the fitment rows on this page. Send the VIN to support if you are unsure.\u003c\/p\u003e\u003ch3\u003eHow does it connect?\u003c\/h3\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced.\u003c\/p\u003e\u003ch3\u003eDoes my Honda Pilot need the factory stop-start button for this to work?\u003c\/h3\u003e\u003cp\u003eYes. The module works with the factory stop-start system and its button. A vehicle built without stop-start has no setting for it to remember.\u003c\/p\u003e\u003ch3\u003eDoes the stop-start button still work after installation on the Honda Pilot?\u003c\/h3\u003e\u003cp\u003eYes. The factory button works normally. The module simply stores whatever you chose last.\u003c\/p\u003e\u003ch3\u003eWhy does Auto Idle Stop turn itself back on every time?\u003c\/h3\u003e\u003cp\u003eAutomakers set stop-start to default to on at each start. Under EPA test rules, a system that stays off after shutdown is tested both on and off and the results are averaged, which lowers the rated fuel economy, so most systems reset at every key cycle. The module carries your last choice across that reset.\u003c\/p\u003e\u003ch2\u003eShipping and support\u003c\/h2\u003e\u003cp\u003eShipping is free to the contiguous US. Orders leave in 1–2 business days and usually arrive 3–4 business days later. Returns are accepted within 45 days with pre-approval; a 20% restocking fee applies and the buyer covers return shipping. The part carries a 3-year limited warranty, and support@automotivebypass.com answers Monday to Friday, 9–5 Pacific.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493788070260,"sku":"RC-ASSE-04-01","price":89.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/2016-2018_Honda_Pilot_Auto_Start-Stop_Eliminators_1.jpg?v=1793347398","url":"https:\/\/automotivebypass.com\/products\/auto-start-stop-eliminator-2016-2018-honda-pilot-auto-start-stop-eliminator","provider":"Automotivebypass","version":"1.0","type":"link"}