{"product_id":"auto-start-stop-eliminator-2018-2021-ford-expedition-auto-start-stop-eliminator","title":"2018-2021 Ford Expedition Auto Start Stop Eliminator","description":"\u003cp\u003eThis inline memory harness is for the 2018–2021 Ford Expedition. It stores the last stop-start setting you chose, so if you turned Auto Start-Stop off on one drive, it stays off the next time you start the engine. It plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced.\u003c\/p\u003e\u003cp\u003eIt does not delete the feature. Turning stop-start back on is the same button press as before, and the module will remember that too. Removing it returns the vehicle to its original default.\u003c\/p\u003e\u003ch2\u003eVehicles and years covered\u003c\/h2\u003e\u003cp\u003eThe fitment table for this SKU lists the following, each marked as a 100% fitment match:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eFord Expedition: 2018–2021\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eThe listing is written around the fourth-generation (2018-up) Expedition. The table does not separate trims; what matters is that the vehicle has factory stop-start and the connector shown in the photos.\u003c\/p\u003e\u003ch2\u003eWhy the button resets\u003c\/h2\u003e\u003cp\u003eEach start of the Ford Expedition begins with Auto Start-Stop enabled. The switch on the dash can disable it, but only until the key is cycled. This module records the switch position and repeats it after the restart, which is the entire job it does.\u003c\/p\u003e\u003ch2\u003eDay-to-day use\u003c\/h2\u003e\u003cp\u003eStop-start saves the most fuel in long idles, but plenty of drivers would rather keep the engine running. Common reasons: towing or hauling, where an engine restart under load is unwelcome; drive-thru lines and parking lots, where the engine cycles on and off every few feet; hot days, when the A\/C compressor stops with the engine on many vehicles; and stop-and-go traffic where the restart delay is noticeable when pulling into a gap. On a full-size SUV, any of these can mean a button press at the start of nearly every drive.\u003c\/p\u003e\u003ch2\u003eKeep the battery healthy\u003c\/h2\u003e\u003cp\u003eMost stop-start systems watch battery condition closely through a sensor on the negative terminal. When the battery ages, the system quietly stops auto-stopping long before the battery fails to crank. Keeping the original battery type (AGM or EFB) and a clean, tight ground connection avoids a lot of confusion about why the system behaves differently from week to week.\u003c\/p\u003e\u003ch2\u003eWhat the module does and does not do\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eComes out in the same way it went in, with nothing cut.\u003c\/li\u003e\n\u003cli\u003eCarries your stop-start choice over to the next drive.\u003c\/li\u003e\n\u003cli\u003eDoes not disable warning lights or diagnostic functions.\u003c\/li\u003e\n\u003cli\u003eFuel use changes only the way it would if you pressed the off button yourself.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhen the engine will not auto-stop anyway\u003c\/h2\u003e\u003cp\u003eAuto stop needs several conditions at once: a warm engine, enough battery charge, moderate cabin heating or cooling demand, and the vehicle fully stopped with the brake held. If any is missing, the engine keeps running. The module only remembers the button state; the factory controller still decides whether a stop is allowed.\u003c\/p\u003e\u003ch2\u003eInstallation and removal\u003c\/h2\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced. Because it is plug-in only, removal is the reverse: unplug the module and reconnect the factory connectors directly. Keep the original clips and trim fasteners if you remove a panel to reach the connector.\u003c\/p\u003e\u003ch2\u003eBefore blaming the module\u003c\/h2\u003e\u003cp\u003eA warning light that appears after installation usually means a connector is not fully seated. Switch the ignition off, reseat both ends until the locks click, and test again. If the light stays on, remove the module and confirm the vehicle is fault-free on its own before contacting support.\u003c\/p\u003e\u003ch2\u003eFitment check\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eModel year and model match a row in the table above (2018–2021 Ford Expedition).\u003c\/li\u003e\n\u003cli\u003eYour Ford Expedition has the factory stop-start button. Base trims or engines without stop-start have nothing for the module to remember.\u003c\/li\u003e\n\u003cli\u003eThe connector at your install point matches the one in the product photos.\u003c\/li\u003e\n\u003cli\u003eThe battery and charging system test good and no warning lights are on.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket remote start, alarm or gateway bypass is wired into the same circuit. If one is, email support before ordering.\u003c\/li\u003e\n\u003cli\u003eIf you are unsure, send your VIN to support@automotivebypass.com and we will confirm fitment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eYear-by-year fitment\u003c\/h2\u003e\u003cp\u003eOne row per model year, taken from the fitment data for this SKU:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2018\u003c\/td\u003e\n\u003ctd\u003eFord\u003c\/td\u003e\n\u003ctd\u003eExpedition\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2019\u003c\/td\u003e\n\u003ctd\u003eFord\u003c\/td\u003e\n\u003ctd\u003eExpedition\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2020\u003c\/td\u003e\n\u003ctd\u003eFord\u003c\/td\u003e\n\u003ctd\u003eExpedition\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2021\u003c\/td\u003e\n\u003ctd\u003eFord\u003c\/td\u003e\n\u003ctd\u003eExpedition\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eGlossary\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eKey cycle:\u003c\/strong\u003e One switch-off and restart of the vehicle. Factory stop-start resets at each key cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAuto Start-Stop:\u003c\/strong\u003e Ford's name for the automatic engine stop-start feature on the Ford Expedition.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNon-latching:\u003c\/strong\u003e A setting that does not stay where the driver left it after a restart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAGM \/ EFB battery:\u003c\/strong\u003e Battery types designed for the frequent cycling of stop-start vehicles.\u003c\/p\u003e\u003ch2\u003eBefore you plug it in\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePark on level ground, shift to Park, switch the ignition off and keep the key or fob away from the vehicle.\u003c\/li\u003e\n\u003cli\u003eRead the included instructions for your model before removing any trim.\u003c\/li\u003e\n\u003cli\u003eLocate the connector named in the instructions and compare it with the plugs on the module.\u003c\/li\u003e\n\u003cli\u003eUse a plastic trim tool where a panel has to be eased out, to avoid marking the dash.\u003c\/li\u003e\n\u003cli\u003ePress each connector until the lock clicks; never force a plug that does not line up.\u003c\/li\u003e\n\u003cli\u003eSecure the module with the supplied tie or tape so it cannot rattle or touch moving parts.\u003c\/li\u003e\n\u003cli\u003eStart the vehicle, set Auto Start-Stop the way you want it, switch off, restart and confirm the setting held.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhy stop-start resets at every start\u003c\/h2\u003e\u003cp\u003eUS fuel-economy testing explains the reset. If a stop-start system is non-latching, meaning it switches back on whenever the vehicle is restarted, the EPA measures fuel economy with the system working. If the driver can switch it off permanently, the EPA tests with it both on and off and averages the two, which gives a lower number. Manufacturers therefore make the system come back on at every start, and drivers who prefer it off end up pressing the button each trip.\u003c\/p\u003e\u003ch2\u003eWhat sits behind the system\u003c\/h2\u003e\u003cp\u003eVehicles with stop-start are built for many more engine starts than a conventional car. They typically use an AGM (absorbent glass mat) or EFB (enhanced flooded) battery that tolerates frequent cycling, along with a strengthened starter. The memory module does not change any of that hardware. When the battery reaches the end of its life, replace it with the same type and size listed for your vehicle, because a standard flooded battery is not designed for this duty.\u003c\/p\u003e\u003ch2\u003eCommon questions after fitting\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eMemory does not hold:\u003c\/strong\u003e Re-seat both plugs until the locks click, then repeat the restart test.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\"Unavailable\" or flashing indicator:\u003c\/strong\u003e A factory condition (battery charge, cabin temperature, engine temperature) is blocking stop-start. The module cannot override it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNew dash message:\u003c\/strong\u003e Disconnect the module and restore the factory connection. If the message goes away, email support with the VIN.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAuto-stop still happens:\u003c\/strong\u003e The last selection was on. Turn Auto Start-Stop off with the button; that state carries over from then on.\u003c\/p\u003e\u003ch2\u003eFAQ\u003c\/h2\u003e\u003ch3\u003eDoes the stop-start button still work after installation on the Ford Expedition?\u003c\/h3\u003e\u003cp\u003eYes. The factory button works normally. The module simply stores whatever you chose last.\u003c\/p\u003e\u003ch3\u003eHow does it connect?\u003c\/h3\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced.\u003c\/p\u003e\u003ch3\u003eWill Auto Start-Stop come back on when I restart my Ford Expedition?\u003c\/h3\u003e\u003cp\u003eNot if you turned it off before shutting down. The module repeats your last selection at the next start. If you leave it on, it stays on.\u003c\/p\u003e\u003ch3\u003eWhich Ford Expedition years does this fit?\u003c\/h3\u003e\u003cp\u003eThe listed range is 2018–2021. Check the fitment table on this page against your exact model year.\u003c\/p\u003e\u003ch3\u003eDoes it change how the battery is charged?\u003c\/h3\u003e\u003cp\u003eNo. Charging is still managed by the vehicle. Stop-start vehicles normally use an AGM or EFB battery built for frequent restarts; replace it with the same type when it wears out.\u003c\/p\u003e\u003ch3\u003eDoes my Ford Expedition need the factory stop-start button for this to work?\u003c\/h3\u003e\u003cp\u003eYes. The module works with the factory stop-start system and its button. A vehicle built without stop-start has no setting for it to remember.\u003c\/p\u003e\u003ch3\u003eWhy does my Ford Expedition sometimes not auto-stop even when the system is on?\u003c\/h3\u003e\u003cp\u003eThe factory logic checks battery charge, engine temperature, climate load and other inputs. If any are outside range it keeps the engine running. The module does not affect those checks.\u003c\/p\u003e\u003ch3\u003eIs this the same part for every Ford?\u003c\/h3\u003e\u003cp\u003eNo. Connectors and the module that holds the stop-start state differ by platform, so this SKU is matched to the fitment rows on this page. Send the VIN to support if you are unsure.\u003c\/p\u003e\u003ch3\u003eWill it fix a \"stop-start unavailable\" message?\u003c\/h3\u003e\u003cp\u003eNo. That message usually points to the battery or a sensor. Diagnose and repair that first.\u003c\/p\u003e\u003ch3\u003eWhat happens if I unplug it?\u003c\/h3\u003e\u003cp\u003eThe vehicle returns to the factory default, with Auto Start-Stop switched on at every start.\u003c\/p\u003e\u003ch3\u003eDoes it change engine power or fuel trims?\u003c\/h3\u003e\u003cp\u003eNo. It does not reprogram the engine or transmission computers. It only stores the stop-start button state.\u003c\/p\u003e\u003ch3\u003eCan I remove it later?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and reconnect the factory connector; the vehicle returns to its stock default.\u003c\/p\u003e\u003ch3\u003eWhy does Auto Start-Stop turn itself back on every time?\u003c\/h3\u003e\u003cp\u003eAutomakers set stop-start to default to on at each start. Under EPA test rules, a system that stays off after shutdown is tested both on and off and the results are averaged, which lowers the rated fuel economy, so most systems reset at every key cycle. The module carries your last choice across that reset.\u003c\/p\u003e\u003ch2\u003eShipping and support\u003c\/h2\u003e\u003cp\u003eStandard shipping inside the lower 48 states costs nothing; allow 1–2 business days of handling plus 3–4 in transit. Returns need approval first and must be requested within 45 days. Approved returns are subject to a 20% restocking fee, with return shipping paid by the customer. A 3-year limited warranty applies. Email support@automotivebypass.com (Mon–Fri, 9–5 PST) with your VIN if you want a fitment check.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493795639668,"sku":"RC-ASSE-15-02","price":89.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/2018-2021_Ford_Expedition_Auto_Start-Stop_Eliminators_1.jpg?v=1793347560","url":"https:\/\/automotivebypass.com\/products\/auto-start-stop-eliminator-2018-2021-ford-expedition-auto-start-stop-eliminator","provider":"Automotivebypass","version":"1.0","type":"link"}