{"product_id":"auto-start-stop-eliminator-2018-2021-ford-expedition-start-stop-memory-harness","title":"2018-2021 Ford Expedition Auto Start Stop Eliminator | Inline Memory Harness","description":"\u003cp\u003eFits the 2018–2021 Ford Expedition. The inline memory harness remembers the position of the stop-start button between drives, so the engine no longer shuts off at the first red light after every restart unless you want it to. It plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced.\u003c\/p\u003e\u003cp\u003eNothing is reprogrammed in the engine computer. The module only stands in for the button press you would otherwise make after every start, and it comes out without leaving a trace.\u003c\/p\u003e\u003ch2\u003eFitment\u003c\/h2\u003e\u003cp\u003eThis part is listed for these vehicles, all marked 100% fitment match:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eFord Expedition: 2018–2021\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eThe listing is written around the fourth-generation (2018-up) Expedition. Trim levels are not split out in the table, so confirm that your vehicle has the stop-start button before ordering.\u003c\/p\u003e\u003ch2\u003eWhy the button resets\u003c\/h2\u003e\u003cp\u003eWith Auto Start-Stop active, the engine shuts off when the vehicle comes to a stop and restarts when you lift off the brake or press the accelerator. The off button is a manual override for that drive only. Turn the ignition off and back on, and the system defaults to on again, so drivers who prefer it off end up pressing the button at the start of every trip.\u003c\/p\u003e\u003ch2\u003eWhat to expect\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLeaves no permanent change after removal.\u003c\/li\u003e\n\u003cli\u003eHolds the stop-start button state between drives.\u003c\/li\u003e\n\u003cli\u003eLets you re-enable the system with the factory button at any time.\u003c\/li\u003e\n\u003cli\u003eLeaves engine and transmission software untouched.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eTypical reasons to keep it off\u003c\/h2\u003e\u003cp\u003eStop-start saves the most fuel in long idles, but plenty of drivers would rather keep the engine running. Common reasons: towing or hauling, where an engine restart under load is unwelcome; drive-thru lines and parking lots, where the engine cycles on and off every few feet; hot days, when the A\/C compressor stops with the engine on many vehicles; and stop-and-go traffic where the restart delay is noticeable when pulling into a gap. On a full-size SUV, any of these can mean a button press at the start of nearly every drive.\u003c\/p\u003e\u003ch2\u003eBefore blaming the module\u003c\/h2\u003e\u003cp\u003eA warning light that appears after installation usually means a connector is not fully seated. Switch the ignition off, reseat both ends until the locks click, and test again. If the light stays on, remove the module and confirm the vehicle is fault-free on its own before contacting support.\u003c\/p\u003e\u003ch2\u003eWhen the engine will not auto-stop anyway\u003c\/h2\u003e\u003cp\u003eThe factory system will skip an auto stop for many reasons: battery charge below its threshold, cold coolant, high climate-control load, a steep grade, the hood or driver door open, or a 4WD or tow mode on vehicles that have them. Those checks stay in control after this module is installed. It does not force stops and it does not bypass any of those safety inputs.\u003c\/p\u003e\u003ch2\u003eKeep the battery healthy\u003c\/h2\u003e\u003cp\u003eVehicles with stop-start normally use an AGM or EFB battery sized for repeated restarts. If you replace it, use the same type and size, and follow the manufacturer's battery reset or registration step where one exists. A wrong or unregistered battery can leave the stop-start system disabled, and that has nothing to do with this module.\u003c\/p\u003e\u003ch2\u003eWhere it connects\u003c\/h2\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced. Disconnect nothing else and splice nothing. Once both plugs are locked, tuck the harness where it will not be pinched when the panel goes back on. Test by switching Auto Start-Stop off, cycling the ignition and checking the indicator.\u003c\/p\u003e\u003ch2\u003eQuick fitment check\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eModel year and model match a row in the table above (2018–2021 Ford Expedition).\u003c\/li\u003e\n\u003cli\u003eYour Ford Expedition has the factory stop-start button. Base trims or engines without stop-start have nothing for the module to remember.\u003c\/li\u003e\n\u003cli\u003eThe connector at your install point matches the one in the product photos.\u003c\/li\u003e\n\u003cli\u003eThe battery and charging system test good and no warning lights are on.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket remote start, alarm or gateway bypass is wired into the same circuit. If one is, email support before ordering.\u003c\/li\u003e\n\u003cli\u003eIf you are unsure, send your VIN to support@automotivebypass.com and we will confirm fitment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eYear-by-year fitment\u003c\/h2\u003e\u003cp\u003eThe full fitment data for this part, by year:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2018\u003c\/td\u003e\n\u003ctd\u003eFord\u003c\/td\u003e\n\u003ctd\u003eExpedition\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2019\u003c\/td\u003e\n\u003ctd\u003eFord\u003c\/td\u003e\n\u003ctd\u003eExpedition\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2020\u003c\/td\u003e\n\u003ctd\u003eFord\u003c\/td\u003e\n\u003ctd\u003eExpedition\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2021\u003c\/td\u003e\n\u003ctd\u003eFord\u003c\/td\u003e\n\u003ctd\u003eExpedition\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eInstall prep checklist\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSwitch everything off and take the key or fob out of range.\u003c\/li\u003e\n\u003cli\u003eGo through the model-specific instructions first.\u003c\/li\u003e\n\u003cli\u003eMatch the vehicle connector to the module before unplugging anything.\u003c\/li\u003e\n\u003cli\u003eRelease clips with a trim tool instead of pulling on wires.\u003c\/li\u003e\n\u003cli\u003eListen for the click on each latch.\u003c\/li\u003e\n\u003cli\u003eTie the module down so it stays quiet and away from moving parts.\u003c\/li\u003e\n\u003cli\u003eRun a restart test to confirm the memory works before refitting trim.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eHardware built for frequent restarts\u003c\/h2\u003e\u003cp\u003eVehicles with stop-start are built for many more engine starts than a conventional car. They typically use an AGM (absorbent glass mat) or EFB (enhanced flooded) battery that tolerates frequent cycling, along with a strengthened starter. The memory module does not change any of that hardware. When the battery reaches the end of its life, replace it with the same type and size listed for your vehicle, because a standard flooded battery is not designed for this duty.\u003c\/p\u003e\u003ch2\u003eQuick definitions\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eKey cycle:\u003c\/strong\u003e One switch-off and restart of the vehicle. Factory stop-start resets at each key cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAGM \/ EFB battery:\u003c\/strong\u003e Battery types designed for the frequent cycling of stop-start vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNon-latching:\u003c\/strong\u003e A setting that does not stay where the driver left it after a restart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAuto Start-Stop:\u003c\/strong\u003e Ford's name for the automatic engine stop-start feature on the Ford Expedition.\u003c\/p\u003e\u003ch2\u003eIf something is not right\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eMemory does not hold:\u003c\/strong\u003e Re-seat both plugs until the locks click, then repeat the restart test.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\"Unavailable\" or flashing indicator:\u003c\/strong\u003e A factory condition (battery charge, cabin temperature, engine temperature) is blocking stop-start. The module cannot override it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNew dash message:\u003c\/strong\u003e Disconnect the module and restore the factory connection. If the message goes away, email support with the VIN.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAuto-stop still happens:\u003c\/strong\u003e The last selection was on. Turn Auto Start-Stop off with the button; that state carries over from then on.\u003c\/p\u003e\u003ch2\u003eWhy the factory default is always on\u003c\/h2\u003e\u003cp\u003eUS fuel-economy testing explains the reset. If a stop-start system is non-latching, meaning it switches back on whenever the vehicle is restarted, the EPA measures fuel economy with the system working. If the driver can switch it off permanently, the EPA tests with it both on and off and averages the two, which gives a lower number. Manufacturers therefore make the system come back on at every start, and drivers who prefer it off end up pressing the button each trip.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWill it fix a \"stop-start unavailable\" message?\u003c\/h3\u003e\u003cp\u003eNo. That message usually points to the battery or a sensor. Diagnose and repair that first.\u003c\/p\u003e\u003ch3\u003eWill Auto Start-Stop come back on when I restart my Ford Expedition?\u003c\/h3\u003e\u003cp\u003eNot if you turned it off before shutting down. The module repeats your last selection at the next start. If you leave it on, it stays on.\u003c\/p\u003e\u003ch3\u003eWhy does my Ford Expedition sometimes not auto-stop even when the system is on?\u003c\/h3\u003e\u003cp\u003eThe factory logic checks battery charge, engine temperature, climate load and other inputs. If any are outside range it keeps the engine running. The module does not affect those checks.\u003c\/p\u003e\u003ch3\u003eWhich Ford Expedition years does this fit?\u003c\/h3\u003e\u003cp\u003eThe listed range is 2018–2021. Check the fitment table on this page against your exact model year.\u003c\/p\u003e\u003ch3\u003eWhat happens if I unplug it?\u003c\/h3\u003e\u003cp\u003eThe vehicle returns to the factory default, with Auto Start-Stop switched on at every start.\u003c\/p\u003e\u003ch3\u003eDoes it change how the battery is charged?\u003c\/h3\u003e\u003cp\u003eNo. Charging is still managed by the vehicle. Stop-start vehicles normally use an AGM or EFB battery built for frequent restarts; replace it with the same type when it wears out.\u003c\/p\u003e\u003ch3\u003eDoes my Ford Expedition need the factory stop-start button for this to work?\u003c\/h3\u003e\u003cp\u003eYes. The module works with the factory stop-start system and its button. A vehicle built without stop-start has no setting for it to remember.\u003c\/p\u003e\u003ch3\u003eDoes the stop-start button still work after installation on the Ford Expedition?\u003c\/h3\u003e\u003cp\u003eYes. The factory button works normally. The module simply stores whatever you chose last.\u003c\/p\u003e\u003ch3\u003eDoes it change engine power or fuel trims?\u003c\/h3\u003e\u003cp\u003eNo. It does not reprogram the engine or transmission computers. It only stores the stop-start button state.\u003c\/p\u003e\u003ch3\u003eHow does it connect?\u003c\/h3\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced.\u003c\/p\u003e\u003ch3\u003eCan I remove it later?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and reconnect the factory connector; the vehicle returns to its stock default.\u003c\/p\u003e\u003ch3\u003eWhy does Auto Start-Stop turn itself back on every time?\u003c\/h3\u003e\u003cp\u003eAutomakers set stop-start to default to on at each start. Under EPA test rules, a system that stays off after shutdown is tested both on and off and the results are averaged, which lowers the rated fuel economy, so most systems reset at every key cycle. The module carries your last choice across that reset.\u003c\/p\u003e\u003ch3\u003eIs this the same part for every Ford?\u003c\/h3\u003e\u003cp\u003eNo. Connectors and the module that holds the stop-start state differ by platform, so this SKU is matched to the fitment rows on this page. Send the VIN to support if you are unsure.\u003c\/p\u003e\u003ch2\u003eShipping, returns and warranty\u003c\/h2\u003e\u003cp\u003eWe ship free within the contiguous United States (1–2 business days to dispatch, roughly 3–4 business days in transit). If it turns out to be the wrong part, request a return authorization within 45 days; returns carry a 20% restocking fee and return postage is on the buyer. Coverage is a 3-year limited warranty. Questions go to support@automotivebypass.com, weekdays 9 a.m. to 5 p.m. PST.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493810745716,"sku":"RC-ASSE-33-02","price":85.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/2018-2021_Ford_Expedition_Auto_Start-Stop_Eliminators_1_b01d1bd9-1ec0-41d6-8fd0-8d5dd5d61fba.jpg?v=1793347915","url":"https:\/\/automotivebypass.com\/products\/auto-start-stop-eliminator-2018-2021-ford-expedition-start-stop-memory-harness","provider":"Automotivebypass","version":"1.0","type":"link"}