{"product_id":"auto-start-stop-eliminator-2018-2024-audi-sq5-auto-start-stop-eliminator","title":"2018-2024 Audi SQ5 Auto Start Stop Eliminator | Plug \u0026 Play","description":"\u003cp\u003eA plug-and-play memory harness for the 2018–2024 Audi SQ5. Out of the factory, start-stop system comes back on at every key cycle. This module remembers your last choice and sends it again at the next start. It plugs in line with the factory connector named in the instructions, using factory-style plugs on both ends, so nothing is cut or spliced.\u003c\/p\u003e\u003cp\u003eThe factory button stays in place and still works. Press it and the module stores the new choice. Unplug the module and the vehicle goes back to stock behavior.\u003c\/p\u003e\u003ch2\u003eFitment\u003c\/h2\u003e\u003cp\u003eListed applications (each row is a 100% fitment match for the factory connector this part uses):\u003c\/p\u003e\u003cul\u003e\u003cli\u003eAudi SQ5: 2018–2024\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eTrim is not listed separately. Any trim in these years with factory stop-start and the pictured connector is covered.\u003c\/p\u003e\u003ch2\u003eHow start-stop system behaves from the factory\u003c\/h2\u003e\u003cp\u003estart-stop system is designed to default to on. The off switch (usually marked with an \"A\" inside a circular arrow) cancels it for the current drive. At the next start the system is armed again. That reset is intentional on the manufacturer's side, and it is the only behavior this module changes.\u003c\/p\u003e\u003ch2\u003eDay-to-day use\u003c\/h2\u003e\u003cp\u003eStop-start saves the most fuel in long idles, but plenty of drivers would rather keep the engine running. Common reasons: towing or hauling, where an engine restart under load is unwelcome; drive-thru lines and parking lots, where the engine cycles on and off every few feet; hot days, when the A\/C compressor stops with the engine on many vehicles; and stop-and-go traffic where the restart delay is noticeable when pulling into a gap. On a daily driver, any of these can mean a button press at the start of nearly every drive.\u003c\/p\u003e\u003ch2\u003eConnecting it\u003c\/h2\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions, using factory-style plugs on both ends, so nothing is cut or spliced. Work with the ignition off. Seat each connector until its lock engages, then secure the module with the supplied ties or tape so it cannot rattle or touch pedals, steering parts or anything hot. Start the vehicle, press the stop-start button once, then restart to confirm the choice is held.\u003c\/p\u003e\u003ch2\u003eDiagnostics first\u003c\/h2\u003e\u003cp\u003eA warning light that appears after installation usually means a connector is not fully seated. Switch the ignition off, reseat both ends until the locks click, and test again. If the light stays on, remove the module and confirm the vehicle is fault-free on its own before contacting support.\u003c\/p\u003e\u003ch2\u003eWhat the module does and does not do\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLeaves no permanent change after removal.\u003c\/li\u003e\n\u003cli\u003eLets you re-enable the system with the factory button at any time.\u003c\/li\u003e\n\u003cli\u003eLeaves engine and transmission software untouched.\u003c\/li\u003e\n\u003cli\u003eHolds the stop-start button state between drives.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eIf stop-start is not engaging\u003c\/h2\u003e\u003cp\u003eAuto stop needs several conditions at once: a warm engine, enough battery charge, moderate cabin heating or cooling demand, and the vehicle fully stopped with the brake held. If any is missing, the engine keeps running. The module only remembers the button state; the factory controller still decides whether a stop is allowed.\u003c\/p\u003e\u003ch2\u003eKeep the battery healthy\u003c\/h2\u003e\u003cp\u003eMost stop-start systems watch battery condition closely through a sensor on the negative terminal. When the battery ages, the system quietly stops auto-stopping long before the battery fails to crank. Keeping the original battery type (AGM or EFB) and a clean, tight ground connection avoids a lot of confusion about why the system behaves differently from week to week.\u003c\/p\u003e\u003ch2\u003eConfirm these points\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eModel year and model match a row in the table above (2018–2024 Audi SQ5).\u003c\/li\u003e\n\u003cli\u003eYour Audi SQ5 has the factory stop-start button. Base trims or engines without stop-start have nothing for the module to remember.\u003c\/li\u003e\n\u003cli\u003eThe battery and charging system test good and no warning lights are on.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket remote start, alarm or gateway bypass is wired into the same circuit. If one is, email support before ordering.\u003c\/li\u003e\n\u003cli\u003eThe connector at your install point matches the one in the product photos.\u003c\/li\u003e\n\u003cli\u003eIf you are unsure, send your VIN to support@automotivebypass.com and we will confirm fitment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment table\u003c\/h2\u003e\u003cp\u003eThe full fitment data for this part, by year:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2018\u003c\/td\u003e\n\u003ctd\u003eAudi\u003c\/td\u003e\n\u003ctd\u003eSQ5\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2019\u003c\/td\u003e\n\u003ctd\u003eAudi\u003c\/td\u003e\n\u003ctd\u003eSQ5\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2020\u003c\/td\u003e\n\u003ctd\u003eAudi\u003c\/td\u003e\n\u003ctd\u003eSQ5\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2021\u003c\/td\u003e\n\u003ctd\u003eAudi\u003c\/td\u003e\n\u003ctd\u003eSQ5\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2022\u003c\/td\u003e\n\u003ctd\u003eAudi\u003c\/td\u003e\n\u003ctd\u003eSQ5\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2023\u003c\/td\u003e\n\u003ctd\u003eAudi\u003c\/td\u003e\n\u003ctd\u003eSQ5\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2024\u003c\/td\u003e\n\u003ctd\u003eAudi\u003c\/td\u003e\n\u003ctd\u003eSQ5\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eInstall prep checklist\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSwitch everything off and take the key or fob out of range.\u003c\/li\u003e\n\u003cli\u003eGo through the model-specific instructions first.\u003c\/li\u003e\n\u003cli\u003eMatch the vehicle connector to the module before unplugging anything.\u003c\/li\u003e\n\u003cli\u003eRelease clips with a trim tool instead of pulling on wires.\u003c\/li\u003e\n\u003cli\u003eListen for the click on each latch.\u003c\/li\u003e\n\u003cli\u003eTie the module down so it stays quiet and away from moving parts.\u003c\/li\u003e\n\u003cli\u003eRun a restart test to confirm the memory works before refitting trim.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eHardware built for frequent restarts\u003c\/h2\u003e\u003cp\u003eVehicles with stop-start are built for many more engine starts than a conventional car. They typically use an AGM (absorbent glass mat) or EFB (enhanced flooded) battery that tolerates frequent cycling, along with a strengthened starter. The memory module does not change any of that hardware. When the battery reaches the end of its life, replace it with the same type and size listed for your vehicle, because a standard flooded battery is not designed for this duty.\u003c\/p\u003e\u003ch2\u003eTroubleshooting after installation\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eMemory does not hold:\u003c\/strong\u003e Re-seat both plugs until the locks click, then repeat the restart test.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\"Unavailable\" or flashing indicator:\u003c\/strong\u003e A factory condition (battery charge, cabin temperature, engine temperature) is blocking stop-start. The module cannot override it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNew dash message:\u003c\/strong\u003e Disconnect the module and restore the factory connection. If the message goes away, email support with the VIN.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAuto-stop still happens:\u003c\/strong\u003e The last selection was on. Turn start-stop system off with the button; that state carries over from then on.\u003c\/p\u003e\u003ch2\u003eWhy the factory default is always on\u003c\/h2\u003e\u003cp\u003eThe factory behavior is tied to how fuel economy is rated in the US. A stop-start system that comes back on at each restart is rated with stop-start active. A system the driver can leave off would be tested both ways and averaged, which lowers the label figure. That is why start-stop system on the Audi SQ5 resets to on, and why a memory module is the way to keep your own preference.\u003c\/p\u003e\u003ch2\u003eGlossary\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eKey cycle:\u003c\/strong\u003e One switch-off and restart of the vehicle. Factory stop-start resets at each key cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003estart-stop system:\u003c\/strong\u003e Audi's name for the automatic engine stop-start feature on the Audi SQ5.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAGM \/ EFB battery:\u003c\/strong\u003e Battery types designed for the frequent cycling of stop-start vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNon-latching:\u003c\/strong\u003e A setting that does not stay where the driver left it after a restart.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhich Audi SQ5 years does this fit?\u003c\/h3\u003e\u003cp\u003eThe listed range is 2018–2024. Check the fitment table on this page against your exact model year.\u003c\/p\u003e\u003ch3\u003eWill start-stop system come back on when I restart my Audi SQ5?\u003c\/h3\u003e\u003cp\u003eNot if you turned it off before shutting down. The module repeats your last selection at the next start. If you leave it on, it stays on.\u003c\/p\u003e\u003ch3\u003eDoes the stop-start button still work after installation on the Audi SQ5?\u003c\/h3\u003e\u003cp\u003eYes. The factory button works normally. The module simply stores whatever you chose last.\u003c\/p\u003e\u003ch3\u003eWill it fix a \"stop-start unavailable\" message?\u003c\/h3\u003e\u003cp\u003eNo. That message usually points to the battery or a sensor. Diagnose and repair that first.\u003c\/p\u003e\u003ch3\u003eIs this the same part for every Audi?\u003c\/h3\u003e\u003cp\u003eNo. Connectors and the module that holds the stop-start state differ by platform, so this SKU is matched to the fitment rows on this page. Send the VIN to support if you are unsure.\u003c\/p\u003e\u003ch3\u003eWhat happens if I unplug it?\u003c\/h3\u003e\u003cp\u003eThe vehicle returns to the factory default, with start-stop system switched on at every start.\u003c\/p\u003e\u003ch3\u003eDoes it change how the battery is charged?\u003c\/h3\u003e\u003cp\u003eNo. Charging is still managed by the vehicle. Stop-start vehicles normally use an AGM or EFB battery built for frequent restarts; replace it with the same type when it wears out.\u003c\/p\u003e\u003ch3\u003eWhy does start-stop system turn itself back on every time?\u003c\/h3\u003e\u003cp\u003eAutomakers set stop-start to default to on at each start. Under EPA test rules, a system that stays off after shutdown is tested both on and off and the results are averaged, which lowers the rated fuel economy, so most systems reset at every key cycle. The module carries your last choice across that reset.\u003c\/p\u003e\u003ch3\u003eDoes my Audi SQ5 need the factory stop-start button for this to work?\u003c\/h3\u003e\u003cp\u003eYes. The module works with the factory stop-start system and its button. A vehicle built without stop-start has no setting for it to remember.\u003c\/p\u003e\u003ch3\u003eWhy does my Audi SQ5 sometimes not auto-stop even when the system is on?\u003c\/h3\u003e\u003cp\u003eThe factory logic checks battery charge, engine temperature, climate load and other inputs. If any are outside range it keeps the engine running. The module does not affect those checks.\u003c\/p\u003e\u003ch3\u003eCan I remove it later?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and reconnect the factory connector; the vehicle returns to its stock default.\u003c\/p\u003e\u003ch3\u003eDoes it change engine power or fuel trims?\u003c\/h3\u003e\u003cp\u003eNo. It does not reprogram the engine or transmission computers. It only stores the stop-start button state.\u003c\/p\u003e\u003ch3\u003eHow does it connect?\u003c\/h3\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions, using factory-style plugs on both ends, so nothing is cut or spliced.\u003c\/p\u003e\u003ch2\u003eShipping and support\u003c\/h2\u003e\u003cp\u003eShipping is free to the contiguous US. Orders leave in 1–2 business days and usually arrive 3–4 business days later. Returns are accepted within 45 days with pre-approval; a 20% restocking fee applies and the buyer covers return shipping. The part carries a 3-year limited warranty, and support@automotivebypass.com answers Monday to Friday, 9–5 Pacific.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493814940020,"sku":"RC-ASSE-50-05","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/2018-2024_Audi_SQ5_Auto_Start-Stop_Eliminators_1.jpg?v=1793348410","url":"https:\/\/automotivebypass.com\/products\/auto-start-stop-eliminator-2018-2024-audi-sq5-auto-start-stop-eliminator","provider":"Automotivebypass","version":"1.0","type":"link"}