{"product_id":"auto-start-stop-eliminator-2019-2020-hyundai-santa-fe-isg-memory-harness","title":"2019-2020 Hyundai Santa Fe auto start stop eliminator with 5.7-inch ISG memory harness. Skip repeated ISG OFF presses while retaining factory control.","description":"\u003cp\u003eThis ISG memory harness is for the 2019–2020 Hyundai Santa Fe. It stores the last stop-start setting you chose, so if you turned ISG (Idle Stop \u0026amp; Go) off on one drive, it stays off the next time you start the engine. It connects at the ISG button circuit, between the switch and its factory plug.\u003c\/p\u003e\u003cp\u003eNothing is reprogrammed in the engine computer. The module only stands in for the button press you would otherwise make after every start, and it comes out without leaving a trace.\u003c\/p\u003e\u003ch2\u003eVehicles and years covered\u003c\/h2\u003e\u003cp\u003eThis part is listed for these vehicles, all marked 100% fitment match:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eHyundai Santa Fe: 2019–2020\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eTrim levels are not split out in the table, so confirm that your vehicle has the stop-start button before ordering.\u003c\/p\u003e\u003ch2\u003eWhy the button resets\u003c\/h2\u003e\u003cp\u003eOn the Hyundai Santa Fe, ISG (Idle Stop \u0026amp; Go) shuts the engine down at a stop and fires it back up as the brake is released. You can switch it off with the dash button, but the choice is not saved. The next ignition cycle brings the default back. The module keeps the choice you made instead.\u003c\/p\u003e\u003ch2\u003eBattery notes for stop-start vehicles\u003c\/h2\u003e\u003cp\u003eIf the stop-start indicator shows the system as unavailable, test the battery before anything else. On stop-start vehicles that is the most common cause. A replacement should match the original specification (AGM or EFB), and some manufacturers call for a battery monitor reset after the swap.\u003c\/p\u003e\u003ch2\u003eWhat the module does and does not do\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCarries your stop-start choice over to the next drive.\u003c\/li\u003e\n\u003cli\u003eComes out in the same way it went in, with nothing cut.\u003c\/li\u003e\n\u003cli\u003eDoes not disable warning lights or diagnostic functions.\u003c\/li\u003e\n\u003cli\u003eFuel use changes only the way it would if you pressed the off button yourself.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eConnecting it\u003c\/h2\u003e\u003cp\u003eIt connects at the ISG button circuit, between the switch and its factory plug. Because it is plug-in only, removal is the reverse: unplug the module and reconnect the factory connectors directly. Keep the original clips and trim fasteners if you remove a panel to reach the connector.\u003c\/p\u003e\u003ch2\u003eTroubleshooting notes\u003c\/h2\u003e\u003cp\u003eA dead or weak battery, a charging problem or an unrelated module fault will change how ISG (Idle Stop \u0026amp; Go) behaves with or without this part installed. Scan the vehicle for stored codes, test the battery and confirm the system works normally with the factory button before installation. That baseline makes any later issue easy to pin down.\u003c\/p\u003e\u003ch2\u003eDay-to-day use\u003c\/h2\u003e\u003cp\u003eSome owners only want stop-start off in certain seasons or on certain trips, such as towing a trailer or crawling through summer traffic with the A\/C working hard. Because the module remembers whatever you chose last, it works both ways: leave the system off for a week, then switch it back on with the factory button and it stays on.\u003c\/p\u003e\u003ch2\u003eThings that already block an auto stop\u003c\/h2\u003e\u003cp\u003eAuto stop needs several conditions at once: a warm engine, enough battery charge, moderate cabin heating or cooling demand, and the vehicle fully stopped with the brake held. If any is missing, the engine keeps running. The module only remembers the button state; the factory controller still decides whether a stop is allowed.\u003c\/p\u003e\u003ch2\u003eFitment check\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eModel year and model match a row in the table above (2019–2020 Hyundai Santa Fe).\u003c\/li\u003e\n\u003cli\u003eYour Hyundai Santa Fe has the factory stop-start button. Base trims or engines without stop-start have nothing for the module to remember.\u003c\/li\u003e\n\u003cli\u003eThe connector at your install point matches the one in the product photos.\u003c\/li\u003e\n\u003cli\u003eThe battery and charging system test good and no warning lights are on.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket remote start, alarm or gateway bypass is wired into the same circuit. If one is, email support before ordering.\u003c\/li\u003e\n\u003cli\u003eIf you are unsure, send your VIN to support@automotivebypass.com and we will confirm fitment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eEvery listed year\u003c\/h2\u003e\u003cp\u003eThe full fitment data for this part, by year:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2019\u003c\/td\u003e\n\u003ctd\u003eHyundai\u003c\/td\u003e\n\u003ctd\u003eSanta Fe\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2020\u003c\/td\u003e\n\u003ctd\u003eHyundai\u003c\/td\u003e\n\u003ctd\u003eSanta Fe\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eQuick definitions\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eISG (Idle Stop \u0026amp; Go):\u003c\/strong\u003e Hyundai's name for the automatic engine stop-start feature on the Hyundai Santa Fe.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eKey cycle:\u003c\/strong\u003e One switch-off and restart of the vehicle. Factory stop-start resets at each key cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNon-latching:\u003c\/strong\u003e A setting that does not stay where the driver left it after a restart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAGM \/ EFB battery:\u003c\/strong\u003e Battery types designed for the frequent cycling of stop-start vehicles.\u003c\/p\u003e\u003ch2\u003eBattery and starter on stop-start vehicles\u003c\/h2\u003e\u003cp\u003eTo cope with repeated restarts, stop-start vehicles normally carry an AGM or EFB battery and a heavier-duty starter, and the system watches battery charge closely. If the battery is weak, the vehicle will skip automatic stops on its own. The module leaves this hardware and its monitoring alone. Use the factory battery type when replacing it, and check the owner's manual for any battery reset step after replacement.\u003c\/p\u003e\u003ch2\u003eThe reason the button has to be pressed every trip\u003c\/h2\u003e\u003cp\u003eThe factory behavior is tied to how fuel economy is rated in the US. A stop-start system that comes back on at each restart is rated with stop-start active. A system the driver can leave off would be tested both ways and averaged, which lowers the label figure. That is why ISG (Idle Stop \u0026amp; Go) on the Hyundai Santa Fe resets to on, and why a memory module is the way to keep your own preference.\u003c\/p\u003e\u003ch2\u003eIf something is not right\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eSetting not remembered:\u003c\/strong\u003e Check that both connectors are fully latched, then set ISG (Idle Stop \u0026amp; Go) the way you want it, switch the vehicle fully off and restart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eStop-start indicator flashes or shows unavailable:\u003c\/strong\u003e The vehicle is reporting a condition such as low battery charge, high climate demand or a cold engine. That comes from the factory logic, not the module.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWarning message after fitting:\u003c\/strong\u003e Unplug the module, reconnect the factory connector and see whether the message clears. Contact support with the VIN and a photo of the connector.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eEngine still stops at lights:\u003c\/strong\u003e That means ISG (Idle Stop \u0026amp; Go) was left on before shutdown. Press the button once to switch it off; the module remembers that choice from the next start.\u003c\/p\u003e\u003ch2\u003eBefore you plug it in\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eIgnition off, transmission in Park, fob outside the cabin.\u003c\/li\u003e\n\u003cli\u003eInstructions for your exact model at hand.\u003c\/li\u003e\n\u003cli\u003eConnector location confirmed against the photos before any panel comes off.\u003c\/li\u003e\n\u003cli\u003eA plastic pry tool for clips, if the connector sits behind trim.\u003c\/li\u003e\n\u003cli\u003eBoth connector locks fully engaged after fitting.\u003c\/li\u003e\n\u003cli\u003eModule and lead fixed in place, clear of pedals, steering and heat.\u003c\/li\u003e\n\u003cli\u003eTest: choose your ISG (Idle Stop \u0026amp; Go) setting, turn the vehicle off, restart and check the indicator.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWill ISG (Idle Stop \u0026amp; Go) come back on when I restart my Hyundai Santa Fe?\u003c\/h3\u003e\u003cp\u003eNot if you turned it off before shutting down. The module repeats your last selection at the next start. If you leave it on, it stays on.\u003c\/p\u003e\u003ch3\u003eWhich Hyundai Santa Fe years does this fit?\u003c\/h3\u003e\u003cp\u003eThe listed range is 2019–2020. Check the fitment table on this page against your exact model year.\u003c\/p\u003e\u003ch3\u003eWhy does my Hyundai Santa Fe sometimes not auto-stop even when the system is on?\u003c\/h3\u003e\u003cp\u003eThe factory logic checks battery charge, engine temperature, climate load and other inputs. If any are outside range it keeps the engine running. The module does not affect those checks.\u003c\/p\u003e\u003ch3\u003eDoes the stop-start button still work after installation on the Hyundai Santa Fe?\u003c\/h3\u003e\u003cp\u003eYes. The factory button works normally. The module simply stores whatever you chose last.\u003c\/p\u003e\u003ch3\u003eDoes it change engine power or fuel trims?\u003c\/h3\u003e\u003cp\u003eNo. It does not reprogram the engine or transmission computers. It only stores the stop-start button state.\u003c\/p\u003e\u003ch3\u003eWill it fix a \"stop-start unavailable\" message?\u003c\/h3\u003e\u003cp\u003eNo. That message usually points to the battery or a sensor. Diagnose and repair that first.\u003c\/p\u003e\u003ch3\u003eWhat happens if I unplug it?\u003c\/h3\u003e\u003cp\u003eThe vehicle returns to the factory default, with ISG (Idle Stop \u0026amp; Go) switched on at every start.\u003c\/p\u003e\u003ch3\u003eDoes it change how the battery is charged?\u003c\/h3\u003e\u003cp\u003eNo. Charging is still managed by the vehicle. Stop-start vehicles normally use an AGM or EFB battery built for frequent restarts; replace it with the same type when it wears out.\u003c\/p\u003e\u003ch3\u003eWhy does ISG (Idle Stop \u0026amp; Go) turn itself back on every time?\u003c\/h3\u003e\u003cp\u003eAutomakers set stop-start to default to on at each start. Under EPA test rules, a system that stays off after shutdown is tested both on and off and the results are averaged, which lowers the rated fuel economy, so most systems reset at every key cycle. The module carries your last choice across that reset.\u003c\/p\u003e\u003ch3\u003eCan I remove it later?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and reconnect the factory connector; the vehicle returns to its stock default.\u003c\/p\u003e\u003ch3\u003eHow does it connect?\u003c\/h3\u003e\u003cp\u003eIt connects at the ISG button circuit, between the switch and its factory plug.\u003c\/p\u003e\u003ch3\u003eDoes my Hyundai Santa Fe need the factory stop-start button for this to work?\u003c\/h3\u003e\u003cp\u003eYes. The module works with the factory stop-start system and its button. A vehicle built without stop-start has no setting for it to remember.\u003c\/p\u003e\u003ch3\u003eIs this the same part for every Hyundai?\u003c\/h3\u003e\u003cp\u003eNo. Connectors and the module that holds the stop-start state differ by platform, so this SKU is matched to the fitment rows on this page. Send the VIN to support if you are unsure.\u003c\/p\u003e\u003ch2\u003eShipping, returns and warranty\u003c\/h2\u003e\u003cp\u003eFree standard shipping covers the contiguous US, with dispatch in 1–2 business days and 3–4 days on the road after that. You have 45 days to request a return (pre-approval required, 20% restocking fee, buyer-paid return shipping). The module is backed by a 3-year limited warranty. For order or fitment questions, write to support@automotivebypass.com between 9 and 5 Pacific, Monday through Friday.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493813432692,"sku":"RC-ASSE-45-01","price":85.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/2019-2020_Hyundai_Santa_Fe_Auto_Start-Stop_Eliminators_1.jpg?v=1793348074","url":"https:\/\/automotivebypass.com\/products\/auto-start-stop-eliminator-2019-2020-hyundai-santa-fe-isg-memory-harness","provider":"Automotivebypass","version":"1.0","type":"link"}