{"product_id":"auto-start-stop-eliminator-2021-2023-hyundai-santa-fe-isg-memory-harness","title":"2021-2023 Hyundai Santa Fe ISG Auto Stop Eliminator | Memory Harness","description":"\u003cp\u003eBuilt for the 2021–2023 Hyundai Santa Fe, this ISG memory harness keeps ISG (Idle Stop \u0026amp; Go) in whatever state you left it. Press the button once, and the setting carries over to the next start. It connects at the ISG button circuit, between the switch and its factory plug.\u003c\/p\u003e\u003cp\u003eThe factory button stays in place and still works. Press it and the module stores the new choice. Unplug the module and the vehicle goes back to stock behavior.\u003c\/p\u003e\u003ch2\u003eWhich Hyundai Santa Fe models it fits\u003c\/h2\u003e\u003cp\u003eEvery row below is listed as a 100% fitment match for this part:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eHyundai Santa Fe: 2021–2023\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eTrim levels are not split out in the table, so confirm that your vehicle has the stop-start button before ordering.\u003c\/p\u003e\u003ch2\u003eHow ISG (Idle Stop \u0026amp; Go) behaves from the factory\u003c\/h2\u003e\u003cp\u003eOn the Hyundai Santa Fe, ISG (Idle Stop \u0026amp; Go) shuts the engine down at a stop and fires it back up as the brake is released. You can switch it off with the dash button, but the choice is not saved. The next ignition cycle brings the default back. The module keeps the choice you made instead.\u003c\/p\u003e\u003ch2\u003eA note on the battery\u003c\/h2\u003e\u003cp\u003eThe module draws its power from the vehicle and does not change charging behavior. If your Hyundai Santa Fe sits for long periods, the same rules apply as without it: a maintainer helps, and a battery that tests weak should be replaced with the type specified for stop-start vehicles (usually AGM or EFB).\u003c\/p\u003e\u003ch2\u003eWhat to expect\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eIt remembers the last stop-start setting through a key cycle.\u003c\/li\u003e\n\u003cli\u003eIt does not write anything to the vehicle's modules, and removing it restores the stock default.\u003c\/li\u003e\n\u003cli\u003eIt does not change engine power, transmission shifts, emissions calibration or fuel trims.\u003c\/li\u003e\n\u003cli\u003eIt leaves the factory button working, so you can turn stop-start back on whenever you want.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eConditions the factory system checks\u003c\/h2\u003e\u003cp\u003eEven with ISG (Idle Stop \u0026amp; Go) enabled, the engine control logic only stops the engine when conditions allow it. Typical blockers are a low battery state of charge, an engine that has not reached operating temperature, heavy heating or A\/C demand, steering input, an open door or unlatched seatbelt, and some drive modes. If the system never seems to stop the engine, one of these is usually the reason, and the module does not change that logic.\u003c\/p\u003e\u003ch2\u003eInstallation and removal\u003c\/h2\u003e\u003cp\u003eIt connects at the ISG button circuit, between the switch and its factory plug. Because it is plug-in only, removal is the reverse: unplug the module and reconnect the factory connectors directly. Keep the original clips and trim fasteners if you remove a panel to reach the connector.\u003c\/p\u003e\u003ch2\u003eWhy owners turn it off\u003c\/h2\u003e\u003cp\u003ePressing the same button on every drive is what wears on owners. People who tow, plow, idle in pickup lines, creep through heavy traffic or simply want the engine running at a light end up making the same press dozens of times a week. On the Hyundai Santa Fe, the module turns that into a one-time choice you can still change whenever you want.\u003c\/p\u003e\u003ch2\u003eTroubleshooting notes\u003c\/h2\u003e\u003cp\u003eA dead or weak battery, a charging problem or an unrelated module fault will change how ISG (Idle Stop \u0026amp; Go) behaves with or without this part installed. Scan the vehicle for stored codes, test the battery and confirm the system works normally with the factory button before installation. That baseline makes any later issue easy to pin down.\u003c\/p\u003e\u003ch2\u003eCheck before you order\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eModel year and model match a row in the table above (2021–2023 Hyundai Santa Fe).\u003c\/li\u003e\n\u003cli\u003eYour Hyundai Santa Fe has the factory stop-start button. Base trims or engines without stop-start have nothing for the module to remember.\u003c\/li\u003e\n\u003cli\u003eThe battery and charging system test good and no warning lights are on.\u003c\/li\u003e\n\u003cli\u003eThe connector at your install point matches the one in the product photos.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket remote start, alarm or gateway bypass is wired into the same circuit. If one is, email support before ordering.\u003c\/li\u003e\n\u003cli\u003eIf you are unsure, send your VIN to support@automotivebypass.com and we will confirm fitment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment table\u003c\/h2\u003e\u003cp\u003eEach model year in the fitment data, listed separately:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2021\u003c\/td\u003e\n\u003ctd\u003eHyundai\u003c\/td\u003e\n\u003ctd\u003eSanta Fe\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2022\u003c\/td\u003e\n\u003ctd\u003eHyundai\u003c\/td\u003e\n\u003ctd\u003eSanta Fe\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2023\u003c\/td\u003e\n\u003ctd\u003eHyundai\u003c\/td\u003e\n\u003ctd\u003eSanta Fe\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eInstall prep checklist\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eIgnition off, transmission in Park, fob outside the cabin.\u003c\/li\u003e\n\u003cli\u003eInstructions for your exact model at hand.\u003c\/li\u003e\n\u003cli\u003eConnector location confirmed against the photos before any panel comes off.\u003c\/li\u003e\n\u003cli\u003eA plastic pry tool for clips, if the connector sits behind trim.\u003c\/li\u003e\n\u003cli\u003eBoth connector locks fully engaged after fitting.\u003c\/li\u003e\n\u003cli\u003eModule and lead fixed in place, clear of pedals, steering and heat.\u003c\/li\u003e\n\u003cli\u003eTest: choose your ISG (Idle Stop \u0026amp; Go) setting, turn the vehicle off, restart and check the indicator.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eBattery and starter on stop-start vehicles\u003c\/h2\u003e\u003cp\u003eVehicles with stop-start are built for many more engine starts than a conventional car. They typically use an AGM (absorbent glass mat) or EFB (enhanced flooded) battery that tolerates frequent cycling, along with a strengthened starter. The memory module does not change any of that hardware. When the battery reaches the end of its life, replace it with the same type and size listed for your vehicle, because a standard flooded battery is not designed for this duty.\u003c\/p\u003e\u003ch2\u003eWhy stop-start resets at every start\u003c\/h2\u003e\u003cp\u003eCar makers have a clear reason to make stop-start non-latching. For EPA ratings, a system that always re-enables itself is counted as on, while one that can stay off is tested on and off and the results averaged. The lower average is something no manufacturer wants on a window sticker, so the default returns at every key cycle.\u003c\/p\u003e\u003ch2\u003eTerms used on this page\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eAGM \/ EFB battery:\u003c\/strong\u003e Battery types designed for the frequent cycling of stop-start vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eISG (Idle Stop \u0026amp; Go):\u003c\/strong\u003e Hyundai's name for the automatic engine stop-start feature on the Hyundai Santa Fe.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eKey cycle:\u003c\/strong\u003e One switch-off and restart of the vehicle. Factory stop-start resets at each key cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNon-latching:\u003c\/strong\u003e A setting that does not stay where the driver left it after a restart.\u003c\/p\u003e\u003ch2\u003eIf something is not right\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eSetting not remembered:\u003c\/strong\u003e Check that both connectors are fully latched, then set ISG (Idle Stop \u0026amp; Go) the way you want it, switch the vehicle fully off and restart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eStop-start indicator flashes or shows unavailable:\u003c\/strong\u003e The vehicle is reporting a condition such as low battery charge, high climate demand or a cold engine. That comes from the factory logic, not the module.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWarning message after fitting:\u003c\/strong\u003e Unplug the module, reconnect the factory connector and see whether the message clears. Contact support with the VIN and a photo of the connector.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eEngine still stops at lights:\u003c\/strong\u003e That means ISG (Idle Stop \u0026amp; Go) was left on before shutdown. Press the button once to switch it off; the module remembers that choice from the next start.\u003c\/p\u003e\u003ch2\u003eQuestions owners ask\u003c\/h2\u003e\u003ch3\u003eDoes the stop-start button still work after installation on the Hyundai Santa Fe?\u003c\/h3\u003e\u003cp\u003eYes. The factory button works normally. The module simply stores whatever you chose last.\u003c\/p\u003e\u003ch3\u003eWhich Hyundai Santa Fe years does this fit?\u003c\/h3\u003e\u003cp\u003eThe listed range is 2021–2023. Check the fitment table on this page against your exact model year.\u003c\/p\u003e\u003ch3\u003eCan I remove it later?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and reconnect the factory connector; the vehicle returns to its stock default.\u003c\/p\u003e\u003ch3\u003eHow does it connect?\u003c\/h3\u003e\u003cp\u003eIt connects at the ISG button circuit, between the switch and its factory plug.\u003c\/p\u003e\u003ch3\u003eWill ISG (Idle Stop \u0026amp; Go) come back on when I restart my Hyundai Santa Fe?\u003c\/h3\u003e\u003cp\u003eNot if you turned it off before shutting down. The module repeats your last selection at the next start. If you leave it on, it stays on.\u003c\/p\u003e\u003ch3\u003eIs this the same part for every Hyundai?\u003c\/h3\u003e\u003cp\u003eNo. Connectors and the module that holds the stop-start state differ by platform, so this SKU is matched to the fitment rows on this page. Send the VIN to support if you are unsure.\u003c\/p\u003e\u003ch3\u003eWill it fix a \"stop-start unavailable\" message?\u003c\/h3\u003e\u003cp\u003eNo. That message usually points to the battery or a sensor. Diagnose and repair that first.\u003c\/p\u003e\u003ch3\u003eWhy does my Hyundai Santa Fe sometimes not auto-stop even when the system is on?\u003c\/h3\u003e\u003cp\u003eThe factory logic checks battery charge, engine temperature, climate load and other inputs. If any are outside range it keeps the engine running. The module does not affect those checks.\u003c\/p\u003e\u003ch3\u003eDoes it change engine power or fuel trims?\u003c\/h3\u003e\u003cp\u003eNo. It does not reprogram the engine or transmission computers. It only stores the stop-start button state.\u003c\/p\u003e\u003ch3\u003eWhat happens if I unplug it?\u003c\/h3\u003e\u003cp\u003eThe vehicle returns to the factory default, with ISG (Idle Stop \u0026amp; Go) switched on at every start.\u003c\/p\u003e\u003ch3\u003eWhy does ISG (Idle Stop \u0026amp; Go) turn itself back on every time?\u003c\/h3\u003e\u003cp\u003eAutomakers set stop-start to default to on at each start. Under EPA test rules, a system that stays off after shutdown is tested both on and off and the results are averaged, which lowers the rated fuel economy, so most systems reset at every key cycle. The module carries your last choice across that reset.\u003c\/p\u003e\u003ch3\u003eDoes my Hyundai Santa Fe need the factory stop-start button for this to work?\u003c\/h3\u003e\u003cp\u003eYes. The module works with the factory stop-start system and its button. A vehicle built without stop-start has no setting for it to remember.\u003c\/p\u003e\u003ch3\u003eDoes it change how the battery is charged?\u003c\/h3\u003e\u003cp\u003eNo. Charging is still managed by the vehicle. Stop-start vehicles normally use an AGM or EFB battery built for frequent restarts; replace it with the same type when it wears out.\u003c\/p\u003e\u003ch2\u003eOrdering details\u003c\/h2\u003e\u003cp\u003eFree standard shipping covers the contiguous US, with dispatch in 1–2 business days and 3–4 days on the road after that. You have 45 days to request a return (pre-approval required, 20% restocking fee, buyer-paid return shipping). The module is backed by a 3-year limited warranty. For order or fitment questions, write to support@automotivebypass.com between 9 and 5 Pacific, Monday through Friday.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493813399924,"sku":"RC-ASSE-44-01","price":82.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/2021-2023_Hyundai_Santa_Fe_Auto_Start-Stop_Eliminators_1.jpg?v=1793348064","url":"https:\/\/automotivebypass.com\/products\/auto-start-stop-eliminator-2021-2023-hyundai-santa-fe-isg-memory-harness","provider":"Automotivebypass","version":"1.0","type":"link"}