{"product_id":"auto-start-stop-eliminator-2021-2026-gmc-yukon-xl-auto-stop-eliminator","title":"2021-2026 GMC Yukon XL Auto Start Stop Eliminator | Plug \u0026 Play","description":"\u003cp\u003eIf your GMC Yukon XL turns Auto Stop\/Start back on every time you start it, this plug-and-play memory harness solves that one problem: it remembers the last setting and restores it at the next ignition cycle. Coverage is the 2021–2026 GMC Yukon XL. It plugs in line with the factory connector named in the instructions, using factory-style plugs on both ends, so nothing is cut or spliced.\u003c\/p\u003e\u003cp\u003eNothing is reprogrammed in the engine computer. The module only stands in for the button press you would otherwise make after every start, and it comes out without leaving a trace.\u003c\/p\u003e\u003ch2\u003eCovered model years\u003c\/h2\u003e\u003cp\u003eThis part is listed for these vehicles, all marked 100% fitment match:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eGMC Yukon XL: 2021–2026\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eThe listing is written around the fifth-generation (2021-up) Yukon XL. Trim is not listed separately. Any trim in these years with factory stop-start and the pictured connector is covered.\u003c\/p\u003e\u003ch2\u003eWhy the button resets\u003c\/h2\u003e\u003cp\u003eThe factory logic arms Auto Stop\/Start every time the engine starts. Turning it off with the button only lasts until the engine is shut down. Owners who sit in stop-and-go traffic, tow, or idle in drive-throughs often prefer it off, and that is where the repeated button press comes from.\u003c\/p\u003e\u003ch2\u003eDiagnostics first\u003c\/h2\u003e\u003cp\u003eIf the setting is not remembered, check that the module was installed with the ignition off and that the connector clicked into place. Then press the factory button once, switch the vehicle off, close the doors, give the electronics time to shut down, and start again. If it still resets, contact support with the year, trim and a photo of the connector.\u003c\/p\u003e\u003ch2\u003eWhy owners turn it off\u003c\/h2\u003e\u003cp\u003ePressing the same button on every drive is what wears on owners. People who tow, plow, idle in pickup lines, creep through heavy traffic or simply want the engine running at a light end up making the same press dozens of times a week. On the GMC Yukon XL, the module turns that into a one-time choice you can still change whenever you want.\u003c\/p\u003e\u003ch2\u003eThings that already block an auto stop\u003c\/h2\u003e\u003cp\u003eThe factory system will skip an auto stop for many reasons: battery charge below its threshold, cold coolant, high climate-control load, a steep grade, the hood or driver door open, or a 4WD or tow mode on vehicles that have them. Those checks stay in control after this module is installed. It does not force stops and it does not bypass any of those safety inputs.\u003c\/p\u003e\u003ch2\u003eKeep the battery healthy\u003c\/h2\u003e\u003cp\u003eThe module draws its power from the vehicle and does not change charging behavior. If your GMC Yukon XL sits for long periods, the same rules apply as without it: a maintainer helps, and a battery that tests weak should be replaced with the type specified for stop-start vehicles (usually AGM or EFB).\u003c\/p\u003e\u003ch2\u003eWhat to expect\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDoes not disable warning lights or diagnostic functions.\u003c\/li\u003e\n\u003cli\u003eCarries your stop-start choice over to the next drive.\u003c\/li\u003e\n\u003cli\u003eComes out in the same way it went in, with nothing cut.\u003c\/li\u003e\n\u003cli\u003eFuel use changes only the way it would if you pressed the off button yourself.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstalling the plug-and-play memory harness\u003c\/h2\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions, using factory-style plugs on both ends, so nothing is cut or spliced. Because it is plug-in only, removal is the reverse: unplug the module and reconnect the factory connectors directly. Keep the original clips and trim fasteners if you remove a panel to reach the connector.\u003c\/p\u003e\u003ch2\u003eQuick fitment check\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eModel year and model match a row in the table above (2021–2026 GMC Yukon XL).\u003c\/li\u003e\n\u003cli\u003eYour GMC Yukon XL has the factory stop-start button. Base trims or engines without stop-start have nothing for the module to remember.\u003c\/li\u003e\n\u003cli\u003eThe battery and charging system test good and no warning lights are on.\u003c\/li\u003e\n\u003cli\u003eThe connector at your install point matches the one in the product photos.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket remote start, alarm or gateway bypass is wired into the same circuit. If one is, email support before ordering.\u003c\/li\u003e\n\u003cli\u003eIf you are unsure, send your VIN to support@automotivebypass.com and we will confirm fitment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eEvery listed year\u003c\/h2\u003e\u003cp\u003eEach model year in the fitment data, listed separately:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2021\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eYukon XL\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2022\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eYukon XL\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2023\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eYukon XL\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2024\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eYukon XL\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2025\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eYukon XL\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2026\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eYukon XL\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eThe reason the button has to be pressed every trip\u003c\/h2\u003e\u003cp\u003eUS fuel-economy testing explains the reset. If a stop-start system is non-latching, meaning it switches back on whenever the vehicle is restarted, the EPA measures fuel economy with the system working. If the driver can switch it off permanently, the EPA tests with it both on and off and averages the two, which gives a lower number. Manufacturers therefore make the system come back on at every start, and drivers who prefer it off end up pressing the button each trip.\u003c\/p\u003e\u003ch2\u003ePreparing for installation\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eIgnition off, transmission in Park, fob outside the cabin.\u003c\/li\u003e\n\u003cli\u003eInstructions for your exact model at hand.\u003c\/li\u003e\n\u003cli\u003eConnector location confirmed against the photos before any panel comes off.\u003c\/li\u003e\n\u003cli\u003eA plastic pry tool for clips, if the connector sits behind trim.\u003c\/li\u003e\n\u003cli\u003eBoth connector locks fully engaged after fitting.\u003c\/li\u003e\n\u003cli\u003eModule and lead fixed in place, clear of pedals, steering and heat.\u003c\/li\u003e\n\u003cli\u003eTest: choose your Auto Stop\/Start setting, turn the vehicle off, restart and check the indicator.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eBattery and starter on stop-start vehicles\u003c\/h2\u003e\u003cp\u003eTo cope with repeated restarts, stop-start vehicles normally carry an AGM or EFB battery and a heavier-duty starter, and the system watches battery charge closely. If the battery is weak, the vehicle will skip automatic stops on its own. The module leaves this hardware and its monitoring alone. Use the factory battery type when replacing it, and check the owner's manual for any battery reset step after replacement.\u003c\/p\u003e\u003ch2\u003eTroubleshooting after installation\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eSetting not remembered:\u003c\/strong\u003e Check that both connectors are fully latched, then set Auto Stop\/Start the way you want it, switch the vehicle fully off and restart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eStop-start indicator flashes or shows unavailable:\u003c\/strong\u003e The vehicle is reporting a condition such as low battery charge, high climate demand or a cold engine. That comes from the factory logic, not the module.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWarning message after fitting:\u003c\/strong\u003e Unplug the module, reconnect the factory connector and see whether the message clears. Contact support with the VIN and a photo of the connector.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eEngine still stops at lights:\u003c\/strong\u003e That means Auto Stop\/Start was left on before shutdown. Press the button once to switch it off; the module remembers that choice from the next start.\u003c\/p\u003e\u003ch2\u003eTerms used on this page\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eAGM \/ EFB battery:\u003c\/strong\u003e Battery types designed for the frequent cycling of stop-start vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAuto Stop\/Start:\u003c\/strong\u003e GMC's name for the automatic engine stop-start feature on the GMC Yukon XL.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eKey cycle:\u003c\/strong\u003e One switch-off and restart of the vehicle. Factory stop-start resets at each key cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNon-latching:\u003c\/strong\u003e A setting that does not stay where the driver left it after a restart.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eCan I remove it later?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and reconnect the factory connector; the vehicle returns to its stock default.\u003c\/p\u003e\u003ch3\u003eWhich GMC Yukon XL years does this fit?\u003c\/h3\u003e\u003cp\u003eThe listed range is 2021–2026. Check the fitment table on this page against your exact model year.\u003c\/p\u003e\u003ch3\u003eWill Auto Stop\/Start come back on when I restart my GMC Yukon XL?\u003c\/h3\u003e\u003cp\u003eNot if you turned it off before shutting down. The module repeats your last selection at the next start. If you leave it on, it stays on.\u003c\/p\u003e\u003ch3\u003eDoes the stop-start button still work after installation on the GMC Yukon XL?\u003c\/h3\u003e\u003cp\u003eYes. The factory button works normally. The module simply stores whatever you chose last.\u003c\/p\u003e\u003ch3\u003eDoes my GMC Yukon XL need the factory stop-start button for this to work?\u003c\/h3\u003e\u003cp\u003eYes. The module works with the factory stop-start system and its button. A vehicle built without stop-start has no setting for it to remember.\u003c\/p\u003e\u003ch3\u003eWhy does Auto Stop\/Start turn itself back on every time?\u003c\/h3\u003e\u003cp\u003eAutomakers set stop-start to default to on at each start. Under EPA test rules, a system that stays off after shutdown is tested both on and off and the results are averaged, which lowers the rated fuel economy, so most systems reset at every key cycle. The module carries your last choice across that reset.\u003c\/p\u003e\u003ch3\u003eWill it fix a \"stop-start unavailable\" message?\u003c\/h3\u003e\u003cp\u003eNo. That message usually points to the battery or a sensor. Diagnose and repair that first.\u003c\/p\u003e\u003ch3\u003eDoes it change engine power or fuel trims?\u003c\/h3\u003e\u003cp\u003eNo. It does not reprogram the engine or transmission computers. It only stores the stop-start button state.\u003c\/p\u003e\u003ch3\u003eDoes it change how the battery is charged?\u003c\/h3\u003e\u003cp\u003eNo. Charging is still managed by the vehicle. Stop-start vehicles normally use an AGM or EFB battery built for frequent restarts; replace it with the same type when it wears out.\u003c\/p\u003e\u003ch3\u003eWhy does my GMC Yukon XL sometimes not auto-stop even when the system is on?\u003c\/h3\u003e\u003cp\u003eThe factory logic checks battery charge, engine temperature, climate load and other inputs. If any are outside range it keeps the engine running. The module does not affect those checks.\u003c\/p\u003e\u003ch3\u003eIs this the same part for every GMC?\u003c\/h3\u003e\u003cp\u003eNo. Connectors and the module that holds the stop-start state differ by platform, so this SKU is matched to the fitment rows on this page. Send the VIN to support if you are unsure.\u003c\/p\u003e\u003ch3\u003eWhat happens if I unplug it?\u003c\/h3\u003e\u003cp\u003eThe vehicle returns to the factory default, with Auto Stop\/Start switched on at every start.\u003c\/p\u003e\u003ch3\u003eHow does it connect?\u003c\/h3\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions, using factory-style plugs on both ends, so nothing is cut or spliced.\u003c\/p\u003e\u003ch2\u003eShipping and support\u003c\/h2\u003e\u003cp\u003eWe ship free within the contiguous United States (1–2 business days to dispatch, roughly 3–4 business days in transit). If it turns out to be the wrong part, request a return authorization within 45 days; returns carry a 20% restocking fee and return postage is on the buyer. Coverage is a 3-year limited warranty. Questions go to support@automotivebypass.com, weekdays 9 a.m. to 5 p.m. PST.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493803536756,"sku":"RC-ASSE-17-04","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/2021-2026_GMC_Yukon_XL_Auto_Start-Stop_Eliminators_1.jpg?v=1793347649","url":"https:\/\/automotivebypass.com\/products\/auto-start-stop-eliminator-2021-2026-gmc-yukon-xl-auto-stop-eliminator","provider":"Automotivebypass","version":"1.0","type":"link"}