{"product_id":"auto-start-stop-eliminator-2024-2025-chevrolet-trax-auto-start-stop-eliminator","title":"2024-2025 Chevrolet Trax  Auto Start Stop Eliminator","description":"\u003cp\u003eA inline memory harness for the 2024–2025 Chevrolet Trax. Out of the factory, Auto Stop\/Start comes back on at every key cycle. This module remembers your last choice and sends it again at the next start. It plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced.\u003c\/p\u003e\u003cp\u003eNothing is reprogrammed in the engine computer. The module only stands in for the button press you would otherwise make after every start, and it comes out without leaving a trace.\u003c\/p\u003e\u003ch2\u003eWhich Chevrolet Trax models it fits\u003c\/h2\u003e\u003cp\u003eThe fitment table for this SKU lists the following, each marked as a 100% fitment match:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eChevrolet Trax: 2024–2025\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eFor reference, the Chevrolet Trax in these years is a subcompact crossover offered with 1.2L turbo three-cylinder engines. The listing is written around the second-generation (2024-up) Trax. Trim is not listed separately. Any trim in these years with factory stop-start and the pictured connector is covered.\u003c\/p\u003e\u003ch2\u003eWhy the button resets\u003c\/h2\u003e\u003cp\u003eAuto Stop\/Start is designed to default to on. The off switch (usually marked with an \"A\" inside a circular arrow) cancels it for the current drive. At the next start the system is armed again. That reset is intentional on the manufacturer's side, and it is the only behavior this module changes.\u003c\/p\u003e\u003ch2\u003eWhat to expect\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLeaves no permanent change after removal.\u003c\/li\u003e\n\u003cli\u003eHolds the stop-start button state between drives.\u003c\/li\u003e\n\u003cli\u003eLeaves engine and transmission software untouched.\u003c\/li\u003e\n\u003cli\u003eLets you re-enable the system with the factory button at any time.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eIf stop-start is not engaging\u003c\/h2\u003e\u003cp\u003eA Chevrolet Trax that rarely auto-stops is often telling you something about the battery. Stop-start vehicles usually run an AGM or EFB battery, and the system is one of the first features to drop out as that battery ages. Cabin temperature requests, engine temperature and brake pressure also factor in. None of these checks are altered by the module.\u003c\/p\u003e\u003ch2\u003eBattery and charging\u003c\/h2\u003e\u003cp\u003eVehicles with stop-start normally use an AGM or EFB battery sized for repeated restarts. If you replace it, use the same type and size, and follow the manufacturer's battery reset or registration step where one exists. A wrong or unregistered battery can leave the stop-start system disabled, and that has nothing to do with this module.\u003c\/p\u003e\u003ch2\u003eWhere it connects\u003c\/h2\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced. Work with the ignition off. Seat each connector until its lock engages, then secure the module with the supplied ties or tape so it cannot rattle or touch pedals, steering parts or anything hot. Start the vehicle, press the stop-start button once, then restart to confirm the choice is held.\u003c\/p\u003e\u003ch2\u003eWhy owners turn it off\u003c\/h2\u003e\u003cp\u003ePressing the same button on every drive is what wears on owners. People who tow, plow, idle in pickup lines, creep through heavy traffic or simply want the engine running at a light end up making the same press dozens of times a week. On the Chevrolet Trax, the module turns that into a one-time choice you can still change whenever you want.\u003c\/p\u003e\u003ch2\u003eIf something does not look right\u003c\/h2\u003e\u003cp\u003eIf the setting is not remembered, check that the module was installed with the ignition off and that the connector clicked into place. Then press the factory button once, switch the vehicle off, close the doors, give the electronics time to shut down, and start again. If it still resets, contact support with the year, trim and a photo of the connector.\u003c\/p\u003e\u003ch2\u003eFitment check\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eModel year and model match a row in the table above (2024–2025 Chevrolet Trax).\u003c\/li\u003e\n\u003cli\u003eYour Chevrolet Trax has the factory stop-start button. Base trims or engines without stop-start have nothing for the module to remember.\u003c\/li\u003e\n\u003cli\u003eThe connector at your install point matches the one in the product photos.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket remote start, alarm or gateway bypass is wired into the same circuit. If one is, email support before ordering.\u003c\/li\u003e\n\u003cli\u003eThe battery and charging system test good and no warning lights are on.\u003c\/li\u003e\n\u003cli\u003eIf you are unsure, send your VIN to support@automotivebypass.com and we will confirm fitment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eYear-by-year fitment\u003c\/h2\u003e\u003cp\u003eThe full fitment data for this part, by year:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2024\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eTrax\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2025\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eTrax\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eInstall prep checklist\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePark on level ground, shift to Park, switch the ignition off and keep the key or fob away from the vehicle.\u003c\/li\u003e\n\u003cli\u003eRead the included instructions for your model before removing any trim.\u003c\/li\u003e\n\u003cli\u003eLocate the connector named in the instructions and compare it with the plugs on the module.\u003c\/li\u003e\n\u003cli\u003eUse a plastic trim tool where a panel has to be eased out, to avoid marking the dash.\u003c\/li\u003e\n\u003cli\u003ePress each connector until the lock clicks; never force a plug that does not line up.\u003c\/li\u003e\n\u003cli\u003eSecure the module with the supplied tie or tape so it cannot rattle or touch moving parts.\u003c\/li\u003e\n\u003cli\u003eStart the vehicle, set Auto Stop\/Start the way you want it, switch off, restart and confirm the setting held.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eThe reason the button has to be pressed every trip\u003c\/h2\u003e\u003cp\u003eCar makers have a clear reason to make stop-start non-latching. For EPA ratings, a system that always re-enables itself is counted as on, while one that can stay off is tested on and off and the results averaged. The lower average is something no manufacturer wants on a window sticker, so the default returns at every key cycle.\u003c\/p\u003e\u003ch2\u003eHardware built for frequent restarts\u003c\/h2\u003e\u003cp\u003eStop-start puts extra load on the battery and starter, so manufacturers fit an AGM or enhanced flooded (EFB) battery and a starter rated for more cycles. Battery state is one of the inputs that decides whether the engine may stop. With the module installed the same rules apply, and the same battery type should be used when it is replaced.\u003c\/p\u003e\u003ch2\u003eQuick definitions\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eAuto Stop\/Start:\u003c\/strong\u003e Chevrolet's name for the automatic engine stop-start feature on the Chevrolet Trax.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eKey cycle:\u003c\/strong\u003e One switch-off and restart of the vehicle. Factory stop-start resets at each key cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNon-latching:\u003c\/strong\u003e A setting that does not stay where the driver left it after a restart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAGM \/ EFB battery:\u003c\/strong\u003e Battery types designed for the frequent cycling of stop-start vehicles.\u003c\/p\u003e\u003ch2\u003eIf something is not right\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eChoice is forgotten after restart:\u003c\/strong\u003e A plug is usually not fully home. Push each until it latches and test again.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIndicator says the system is unavailable:\u003c\/strong\u003e The vehicle has decided conditions are not right for an automatic stop. This is normal factory behavior.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWarning appears:\u003c\/strong\u003e Remove the module, reconnect the original plug and confirm the warning clears, then contact support.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eEngine keeps shutting off at stops:\u003c\/strong\u003e Switch Auto Stop\/Start off once. The module stores the off state for the next start.\u003c\/p\u003e\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\u003ch3\u003eDoes it change engine power or fuel trims?\u003c\/h3\u003e\u003cp\u003eNo. It does not reprogram the engine or transmission computers. It only stores the stop-start button state.\u003c\/p\u003e\u003ch3\u003eWill Auto Stop\/Start come back on when I restart my Chevrolet Trax?\u003c\/h3\u003e\u003cp\u003eNot if you turned it off before shutting down. The module repeats your last selection at the next start. If you leave it on, it stays on.\u003c\/p\u003e\u003ch3\u003eCan I remove it later?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and reconnect the factory connector; the vehicle returns to its stock default.\u003c\/p\u003e\u003ch3\u003eWhich Chevrolet Trax years does this fit?\u003c\/h3\u003e\u003cp\u003eThe listed range is 2024–2025. Check the fitment table on this page against your exact model year.\u003c\/p\u003e\u003ch3\u003eHow does it connect?\u003c\/h3\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions. Both ends are factory-style plugs, so nothing is cut or spliced.\u003c\/p\u003e\u003ch3\u003eDoes the stop-start button still work after installation on the Chevrolet Trax?\u003c\/h3\u003e\u003cp\u003eYes. The factory button works normally. The module simply stores whatever you chose last.\u003c\/p\u003e\u003ch3\u003eDoes it change how the battery is charged?\u003c\/h3\u003e\u003cp\u003eNo. Charging is still managed by the vehicle. Stop-start vehicles normally use an AGM or EFB battery built for frequent restarts; replace it with the same type when it wears out.\u003c\/p\u003e\u003ch3\u003eWill it fix a \"stop-start unavailable\" message?\u003c\/h3\u003e\u003cp\u003eNo. That message usually points to the battery or a sensor. Diagnose and repair that first.\u003c\/p\u003e\u003ch3\u003eWhy does Auto Stop\/Start turn itself back on every time?\u003c\/h3\u003e\u003cp\u003eAutomakers set stop-start to default to on at each start. Under EPA test rules, a system that stays off after shutdown is tested both on and off and the results are averaged, which lowers the rated fuel economy, so most systems reset at every key cycle. The module carries your last choice across that reset.\u003c\/p\u003e\u003ch3\u003eWhat happens if I unplug it?\u003c\/h3\u003e\u003cp\u003eThe vehicle returns to the factory default, with Auto Stop\/Start switched on at every start.\u003c\/p\u003e\u003ch3\u003eIs this the same part for every Chevrolet?\u003c\/h3\u003e\u003cp\u003eNo. Connectors and the module that holds the stop-start state differ by platform, so this SKU is matched to the fitment rows on this page. Send the VIN to support if you are unsure.\u003c\/p\u003e\u003ch3\u003eWhy does my Chevrolet Trax sometimes not auto-stop even when the system is on?\u003c\/h3\u003e\u003cp\u003eThe factory logic checks battery charge, engine temperature, climate load and other inputs. If any are outside range it keeps the engine running. The module does not affect those checks.\u003c\/p\u003e\u003ch3\u003eDoes my Chevrolet Trax need the factory stop-start button for this to work?\u003c\/h3\u003e\u003cp\u003eYes. The module works with the factory stop-start system and its button. A vehicle built without stop-start has no setting for it to remember.\u003c\/p\u003e\u003ch2\u003eOrdering details\u003c\/h2\u003e\u003cp\u003eWe ship free within the contiguous United States (1–2 business days to dispatch, roughly 3–4 business days in transit). If it turns out to be the wrong part, request a return authorization within 45 days; returns carry a 20% restocking fee and return postage is on the buyer. Coverage is a 3-year limited warranty. Questions go to support@automotivebypass.com, weekdays 9 a.m. to 5 p.m. PST.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493783286132,"sku":"RC-ASSE-01-03","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/2024-2025_Chevrolet_Trax_Auto_Start-Stop_Eliminators_1.jpg?v=1793347296","url":"https:\/\/automotivebypass.com\/products\/auto-start-stop-eliminator-2024-2025-chevrolet-trax-auto-start-stop-eliminator","provider":"Automotivebypass","version":"1.0","type":"link"}