{"product_id":"auto-start-stop-eliminator-2024-2026-subaru-crosstrek-fused-memory-module","title":"2024-2026 Subaru Crosstrek Auto Start Stop Eliminator | Fused Memory Harness","description":"\u003cp\u003eBuilt for the 2024–2026 Subaru Crosstrek, this fused memory harness keeps Auto Start Stop in whatever state you left it. Press the button once, and the setting carries over to the next start. The harness connects at the stop-start switch circuit and includes an inline fuse on its power lead.\u003c\/p\u003e\u003cp\u003eIt does not delete the feature. Turning stop-start back on is the same button press as before, and the module will remember that too. Removing it returns the vehicle to its original default.\u003c\/p\u003e\u003ch2\u003eCovered model years\u003c\/h2\u003e\u003cp\u003eThis part is listed for these vehicles, all marked 100% fitment match:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eSubaru Crosstrek: 2024–2026\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eFor reference, the Subaru Crosstrek in these years is a subcompact crossover offered with 2.0L and 2.5L flat-four engines. The listing is written around the third-generation (2024-up) Crosstrek. The table does not separate trims; what matters is that the vehicle has factory stop-start and the connector shown in the photos.\u003c\/p\u003e\u003ch2\u003eWhy the button resets\u003c\/h2\u003e\u003cp\u003eWith Auto Start Stop active, the engine shuts off when the vehicle comes to a stop and restarts when you lift off the brake or press the accelerator. The off button is a manual override for that drive only. Turn the ignition off and back on, and the system defaults to on again, so drivers who prefer it off end up pressing the button at the start of every trip.\u003c\/p\u003e\u003ch2\u003eA note on the battery\u003c\/h2\u003e\u003cp\u003eIf the stop-start indicator shows the system as unavailable, test the battery before anything else. On stop-start vehicles that is the most common cause. A replacement should match the original specification (AGM or EFB), and some manufacturers call for a battery monitor reset after the swap.\u003c\/p\u003e\u003ch2\u003eWhat changes after installation\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eIt leaves the factory button working, so you can turn stop-start back on whenever you want.\u003c\/li\u003e\n\u003cli\u003eIt does not change engine power, transmission shifts, emissions calibration or fuel trims.\u003c\/li\u003e\n\u003cli\u003eIt remembers the last stop-start setting through a key cycle.\u003c\/li\u003e\n\u003cli\u003eIt does not write anything to the vehicle's modules, and removing it restores the stock default.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eConditions the factory system checks\u003c\/h2\u003e\u003cp\u003eA Subaru Crosstrek that rarely auto-stops is often telling you something about the battery. Stop-start vehicles usually run an AGM or EFB battery, and the system is one of the first features to drop out as that battery ages. Cabin temperature requests, engine temperature and brake pressure also factor in. None of these checks are altered by the module.\u003c\/p\u003e\u003ch2\u003eWhy owners turn it off\u003c\/h2\u003e\u003cp\u003eSome owners only want stop-start off in certain seasons or on certain trips, such as towing a trailer or crawling through summer traffic with the A\/C working hard. Because the module remembers whatever you chose last, it works both ways: leave the system off for a week, then switch it back on with the factory button and it stays on.\u003c\/p\u003e\u003ch2\u003eIf something does not look right\u003c\/h2\u003e\u003cp\u003eIf the setting is not remembered, check that the module was installed with the ignition off and that the connector clicked into place. Then press the factory button once, switch the vehicle off, close the doors, give the electronics time to shut down, and start again. If it still resets, contact support with the year, trim and a photo of the connector.\u003c\/p\u003e\u003ch2\u003eWhere it connects\u003c\/h2\u003e\u003cp\u003eThe harness connects at the stop-start switch circuit and includes an inline fuse on its power lead. The instructions show the connector for this application; compare it with the product photos before starting. Turn the vehicle off, make the connection, fix the module in place, and test with two or three key cycles.\u003c\/p\u003e\u003ch2\u003eConfirm these points\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eModel year and model match a row in the table above (2024–2026 Subaru Crosstrek).\u003c\/li\u003e\n\u003cli\u003eYour Subaru Crosstrek has the factory stop-start button. Base trims or engines without stop-start have nothing for the module to remember.\u003c\/li\u003e\n\u003cli\u003eThe connector at your install point matches the one in the product photos.\u003c\/li\u003e\n\u003cli\u003eThe battery and charging system test good and no warning lights are on.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket remote start, alarm or gateway bypass is wired into the same circuit. If one is, email support before ordering.\u003c\/li\u003e\n\u003cli\u003eIf you are unsure, send your VIN to support@automotivebypass.com and we will confirm fitment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eYear-by-year fitment\u003c\/h2\u003e\u003cp\u003eEach model year in the fitment data, listed separately:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2024\u003c\/td\u003e\n\u003ctd\u003eSubaru\u003c\/td\u003e\n\u003ctd\u003eCrosstrek\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2025\u003c\/td\u003e\n\u003ctd\u003eSubaru\u003c\/td\u003e\n\u003ctd\u003eCrosstrek\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2026\u003c\/td\u003e\n\u003ctd\u003eSubaru\u003c\/td\u003e\n\u003ctd\u003eCrosstrek\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eTerms used on this page\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eKey cycle:\u003c\/strong\u003e One switch-off and restart of the vehicle. Factory stop-start resets at each key cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAGM \/ EFB battery:\u003c\/strong\u003e Battery types designed for the frequent cycling of stop-start vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAuto Start Stop:\u003c\/strong\u003e Subaru's name for the automatic engine stop-start feature on the Subaru Crosstrek.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNon-latching:\u003c\/strong\u003e A setting that does not stay where the driver left it after a restart.\u003c\/p\u003e\u003ch2\u003eHardware built for frequent restarts\u003c\/h2\u003e\u003cp\u003eTo cope with repeated restarts, stop-start vehicles normally carry an AGM or EFB battery and a heavier-duty starter, and the system watches battery charge closely. If the battery is weak, the vehicle will skip automatic stops on its own. The module leaves this hardware and its monitoring alone. Use the factory battery type when replacing it, and check the owner's manual for any battery reset step after replacement.\u003c\/p\u003e\u003ch2\u003ePreparing for installation\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePark on level ground, shift to Park, switch the ignition off and keep the key or fob away from the vehicle.\u003c\/li\u003e\n\u003cli\u003eRead the included instructions for your model before removing any trim.\u003c\/li\u003e\n\u003cli\u003eLocate the connector named in the instructions and compare it with the plugs on the module.\u003c\/li\u003e\n\u003cli\u003eUse a plastic trim tool where a panel has to be eased out, to avoid marking the dash.\u003c\/li\u003e\n\u003cli\u003ePress each connector until the lock clicks; never force a plug that does not line up.\u003c\/li\u003e\n\u003cli\u003eSecure the module with the supplied tie or tape so it cannot rattle or touch moving parts.\u003c\/li\u003e\n\u003cli\u003eStart the vehicle, set Auto Start Stop the way you want it, switch off, restart and confirm the setting held.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhy stop-start resets at every start\u003c\/h2\u003e\u003cp\u003eThe factory behavior is tied to how fuel economy is rated in the US. A stop-start system that comes back on at each restart is rated with stop-start active. A system the driver can leave off would be tested both ways and averaged, which lowers the label figure. That is why Auto Start Stop on the Subaru Crosstrek resets to on, and why a memory module is the way to keep your own preference.\u003c\/p\u003e\u003ch2\u003eTroubleshooting after installation\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eMemory does not hold:\u003c\/strong\u003e Re-seat both plugs until the locks click, then repeat the restart test.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\"Unavailable\" or flashing indicator:\u003c\/strong\u003e A factory condition (battery charge, cabin temperature, engine temperature) is blocking stop-start. The module cannot override it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNew dash message:\u003c\/strong\u003e Disconnect the module and restore the factory connection. If the message goes away, email support with the VIN.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAuto-stop still happens:\u003c\/strong\u003e The last selection was on. Turn Auto Start Stop off with the button; that state carries over from then on.\u003c\/p\u003e\u003ch2\u003eFAQ\u003c\/h2\u003e\u003ch3\u003eWill Auto Start Stop come back on when I restart my Subaru Crosstrek?\u003c\/h3\u003e\u003cp\u003eNot if you turned it off before shutting down. The module repeats your last selection at the next start. If you leave it on, it stays on.\u003c\/p\u003e\u003ch3\u003eWhy does my Subaru Crosstrek sometimes not auto-stop even when the system is on?\u003c\/h3\u003e\u003cp\u003eThe factory logic checks battery charge, engine temperature, climate load and other inputs. If any are outside range it keeps the engine running. The module does not affect those checks.\u003c\/p\u003e\u003ch3\u003eDoes it change engine power or fuel trims?\u003c\/h3\u003e\u003cp\u003eNo. It does not reprogram the engine or transmission computers. It only stores the stop-start button state.\u003c\/p\u003e\u003ch3\u003eWhich Subaru Crosstrek years does this fit?\u003c\/h3\u003e\u003cp\u003eThe listed range is 2024–2026. Check the fitment table on this page against your exact model year.\u003c\/p\u003e\u003ch3\u003eDoes the stop-start button still work after installation on the Subaru Crosstrek?\u003c\/h3\u003e\u003cp\u003eYes. The factory button works normally. The module simply stores whatever you chose last.\u003c\/p\u003e\u003ch3\u003eDoes it change how the battery is charged?\u003c\/h3\u003e\u003cp\u003eNo. Charging is still managed by the vehicle. Stop-start vehicles normally use an AGM or EFB battery built for frequent restarts; replace it with the same type when it wears out.\u003c\/p\u003e\u003ch3\u003eDoes my Subaru Crosstrek need the factory stop-start button for this to work?\u003c\/h3\u003e\u003cp\u003eYes. The module works with the factory stop-start system and its button. A vehicle built without stop-start has no setting for it to remember.\u003c\/p\u003e\u003ch3\u003eWhat happens if I unplug it?\u003c\/h3\u003e\u003cp\u003eThe vehicle returns to the factory default, with Auto Start Stop switched on at every start.\u003c\/p\u003e\u003ch3\u003eIs this the same part for every Subaru?\u003c\/h3\u003e\u003cp\u003eNo. Connectors and the module that holds the stop-start state differ by platform, so this SKU is matched to the fitment rows on this page. Send the VIN to support if you are unsure.\u003c\/p\u003e\u003ch3\u003eHow does it connect?\u003c\/h3\u003e\u003cp\u003eThe harness connects at the stop-start switch circuit and includes an inline fuse on its power lead.\u003c\/p\u003e\u003ch3\u003eWill it fix a \"stop-start unavailable\" message?\u003c\/h3\u003e\u003cp\u003eNo. That message usually points to the battery or a sensor. Diagnose and repair that first.\u003c\/p\u003e\u003ch3\u003eCan I remove it later?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and reconnect the factory connector; the vehicle returns to its stock default.\u003c\/p\u003e\u003ch3\u003eWhy does Auto Start Stop turn itself back on every time?\u003c\/h3\u003e\u003cp\u003eAutomakers set stop-start to default to on at each start. Under EPA test rules, a system that stays off after shutdown is tested both on and off and the results are averaged, which lowers the rated fuel economy, so most systems reset at every key cycle. The module carries your last choice across that reset.\u003c\/p\u003e\u003ch2\u003eShipping, returns and warranty\u003c\/h2\u003e\u003cp\u003eWe ship free within the contiguous United States (1–2 business days to dispatch, roughly 3–4 business days in transit). If it turns out to be the wrong part, request a return authorization within 45 days; returns carry a 20% restocking fee and return postage is on the buyer. Coverage is a 3-year limited warranty. Questions go to support@automotivebypass.com, weekdays 9 a.m. to 5 p.m. PST.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493811564916,"sku":"RC-ASSE-37-01","price":95.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/2024-2026_Subarud_Crosstrek_Auto_Start-Stop_Eliminators_1.jpg?v=1793347952","url":"https:\/\/automotivebypass.com\/products\/auto-start-stop-eliminator-2024-2026-subaru-crosstrek-fused-memory-module","provider":"Automotivebypass","version":"1.0","type":"link"}