{"product_id":"auto-start-stop-eliminator-2025-2026-dodge-ram-1500-4wd-auto-start-stop-eliminator","title":"2025-2026 Dodge RAM 1500 4-Wheel Drive Auto Start Stop Eliminator | Plug \u0026 Play","description":"\u003cp\u003eBuilt for the 2025–2026 Dodge RAM 1500, this plug-and-play memory harness keeps Engine Stop-Start (ESS) in whatever state you left it. Press the button once, and the setting carries over to the next start. It plugs in line with the factory connector named in the instructions, using factory-style plugs on both ends, so nothing is cut or spliced.\u003c\/p\u003e\u003cp\u003eThe factory button stays in place and still works. Press it and the module stores the new choice. Unplug the module and the vehicle goes back to stock behavior.\u003c\/p\u003e\u003ch2\u003eCovered model years\u003c\/h2\u003e\u003cp\u003eThis part is listed for these vehicles, all marked 100% fitment match:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eDodge RAM 1500: 2025–2026\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eFor reference, the Dodge RAM 1500 in these years is a full-size pickup offered with 3.6L V6 and 5.7L HEMI V8 engines with eTorque, earlier 3.0L EcoDiesel builds and the 3.0L Hurricane turbo six on 2025-up trucks. Trim levels are not split out in the table, so confirm that your vehicle has the stop-start button before ordering.\u003c\/p\u003e\u003ch2\u003eWhat the factory system does\u003c\/h2\u003e\u003cp\u003eEach start of the Dodge RAM 1500 begins with Engine Stop-Start (ESS) enabled. The switch on the dash can disable it, but only until the key is cycled. This module records the switch position and repeats it after the restart, which is the entire job it does.\u003c\/p\u003e\u003ch2\u003eBefore blaming the module\u003c\/h2\u003e\u003cp\u003eA warning light that appears after installation usually means a connector is not fully seated. Switch the ignition off, reseat both ends until the locks click, and test again. If the light stays on, remove the module and confirm the vehicle is fault-free on its own before contacting support.\u003c\/p\u003e\u003ch2\u003eInstallation and removal\u003c\/h2\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions, using factory-style plugs on both ends, so nothing is cut or spliced. Disconnect nothing else and splice nothing. Once both plugs are locked, tuck the harness where it will not be pinched when the panel goes back on. Test by switching Engine Stop-Start (ESS) off, cycling the ignition and checking the indicator.\u003c\/p\u003e\u003ch2\u003eIf stop-start is not engaging\u003c\/h2\u003e\u003cp\u003eThe factory system will skip an auto stop for many reasons: battery charge below its threshold, cold coolant, high climate-control load, a steep grade, the hood or driver door open, or a 4WD or tow mode on vehicles that have them. Those checks stay in control after this module is installed. It does not force stops and it does not bypass any of those safety inputs.\u003c\/p\u003e\u003ch2\u003eScope of the module\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStores the stop-start choice you made last and repeats it at the next start.\u003c\/li\u003e\n\u003cli\u003eNo tune, no reflash, no change to horsepower or shift points.\u003c\/li\u003e\n\u003cli\u003eFully reversible: unplug it and the vehicle returns to factory behavior.\u003c\/li\u003e\n\u003cli\u003eKeeps the original switch fully functional.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhy owners turn it off\u003c\/h2\u003e\u003cp\u003ePressing the same button on every drive is what wears on owners. People who tow, plow, idle in pickup lines, creep through heavy traffic or simply want the engine running at a light end up making the same press dozens of times a week. On the Dodge RAM 1500, the module turns that into a one-time choice you can still change whenever you want.\u003c\/p\u003e\u003ch2\u003eA note on the battery\u003c\/h2\u003e\u003cp\u003eThe module draws its power from the vehicle and does not change charging behavior. If your Dodge RAM 1500 sits for long periods, the same rules apply as without it: a maintainer helps, and a battery that tests weak should be replaced with the type specified for stop-start vehicles (usually AGM or EFB).\u003c\/p\u003e\u003ch2\u003eCheck before you order\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eModel year and model match a row in the table above (2025–2026 Dodge RAM 1500).\u003c\/li\u003e\n\u003cli\u003eYour Dodge RAM 1500 has the factory stop-start button. Base trims or engines without stop-start have nothing for the module to remember.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket remote start, alarm or gateway bypass is wired into the same circuit. If one is, email support before ordering.\u003c\/li\u003e\n\u003cli\u003eThe battery and charging system test good and no warning lights are on.\u003c\/li\u003e\n\u003cli\u003eThe connector at your install point matches the one in the product photos.\u003c\/li\u003e\n\u003cli\u003eIf you are unsure, send your VIN to support@automotivebypass.com and we will confirm fitment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eEvery listed year\u003c\/h2\u003e\u003cp\u003eOne row per model year, taken from the fitment data for this SKU:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2025\u003c\/td\u003e\n\u003ctd\u003eDodge\u003c\/td\u003e\n\u003ctd\u003eRAM 1500\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2026\u003c\/td\u003e\n\u003ctd\u003eDodge\u003c\/td\u003e\n\u003ctd\u003eRAM 1500\u003c\/td\u003e\n\u003ctd\u003eAll with factory stop-start\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eHardware built for frequent restarts\u003c\/h2\u003e\u003cp\u003eStop-start puts extra load on the battery and starter, so manufacturers fit an AGM or enhanced flooded (EFB) battery and a starter rated for more cycles. Battery state is one of the inputs that decides whether the engine may stop. With the module installed the same rules apply, and the same battery type should be used when it is replaced.\u003c\/p\u003e\u003ch2\u003eWhy stop-start resets at every start\u003c\/h2\u003e\u003cp\u003eCar makers have a clear reason to make stop-start non-latching. For EPA ratings, a system that always re-enables itself is counted as on, while one that can stay off is tested on and off and the results averaged. The lower average is something no manufacturer wants on a window sticker, so the default returns at every key cycle.\u003c\/p\u003e\u003ch2\u003eTroubleshooting after installation\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eSetting not remembered:\u003c\/strong\u003e Check that both connectors are fully latched, then set Engine Stop-Start (ESS) the way you want it, switch the vehicle fully off and restart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eStop-start indicator flashes or shows unavailable:\u003c\/strong\u003e The vehicle is reporting a condition such as low battery charge, high climate demand or a cold engine. That comes from the factory logic, not the module.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWarning message after fitting:\u003c\/strong\u003e Unplug the module, reconnect the factory connector and see whether the message clears. Contact support with the VIN and a photo of the connector.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eEngine still stops at lights:\u003c\/strong\u003e That means Engine Stop-Start (ESS) was left on before shutdown. Press the button once to switch it off; the module remembers that choice from the next start.\u003c\/p\u003e\u003ch2\u003eGlossary\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eKey cycle:\u003c\/strong\u003e One switch-off and restart of the vehicle. Factory stop-start resets at each key cycle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eEngine Stop-Start (ESS):\u003c\/strong\u003e Dodge's name for the automatic engine stop-start feature on the Dodge RAM 1500.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNon-latching:\u003c\/strong\u003e A setting that does not stay where the driver left it after a restart.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAGM \/ EFB battery:\u003c\/strong\u003e Battery types designed for the frequent cycling of stop-start vehicles.\u003c\/p\u003e\u003ch2\u003eBefore you plug it in\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePark on level ground, shift to Park, switch the ignition off and keep the key or fob away from the vehicle.\u003c\/li\u003e\n\u003cli\u003eRead the included instructions for your model before removing any trim.\u003c\/li\u003e\n\u003cli\u003eLocate the connector named in the instructions and compare it with the plugs on the module.\u003c\/li\u003e\n\u003cli\u003eUse a plastic trim tool where a panel has to be eased out, to avoid marking the dash.\u003c\/li\u003e\n\u003cli\u003ePress each connector until the lock clicks; never force a plug that does not line up.\u003c\/li\u003e\n\u003cli\u003eSecure the module with the supplied tie or tape so it cannot rattle or touch moving parts.\u003c\/li\u003e\n\u003cli\u003eStart the vehicle, set Engine Stop-Start (ESS) the way you want it, switch off, restart and confirm the setting held.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\u003ch3\u003eDoes the stop-start button still work after installation on the Dodge RAM 1500?\u003c\/h3\u003e\u003cp\u003eYes. The factory button works normally. The module simply stores whatever you chose last.\u003c\/p\u003e\u003ch3\u003eDoes it change engine power or fuel trims?\u003c\/h3\u003e\u003cp\u003eNo. It does not reprogram the engine or transmission computers. It only stores the stop-start button state.\u003c\/p\u003e\u003ch3\u003eWhich Dodge RAM 1500 years does this fit?\u003c\/h3\u003e\u003cp\u003eThe listed range is 2025–2026. Check the fitment table on this page against your exact model year.\u003c\/p\u003e\u003ch3\u003eWill Engine Stop-Start (ESS) come back on when I restart my Dodge RAM 1500?\u003c\/h3\u003e\u003cp\u003eNot if you turned it off before shutting down. The module repeats your last selection at the next start. If you leave it on, it stays on.\u003c\/p\u003e\u003ch3\u003eCan I remove it later?\u003c\/h3\u003e\u003cp\u003eYes. Unplug the module and reconnect the factory connector; the vehicle returns to its stock default.\u003c\/p\u003e\u003ch3\u003eWill it fix a \"stop-start unavailable\" message?\u003c\/h3\u003e\u003cp\u003eNo. That message usually points to the battery or a sensor. Diagnose and repair that first.\u003c\/p\u003e\u003ch3\u003eIs this the same part for every Dodge?\u003c\/h3\u003e\u003cp\u003eNo. Connectors and the module that holds the stop-start state differ by platform, so this SKU is matched to the fitment rows on this page. Send the VIN to support if you are unsure.\u003c\/p\u003e\u003ch3\u003eWhat happens if I unplug it?\u003c\/h3\u003e\u003cp\u003eThe vehicle returns to the factory default, with Engine Stop-Start (ESS) switched on at every start.\u003c\/p\u003e\u003ch3\u003eWhy does Engine Stop-Start (ESS) turn itself back on every time?\u003c\/h3\u003e\u003cp\u003eAutomakers set stop-start to default to on at each start. Under EPA test rules, a system that stays off after shutdown is tested both on and off and the results are averaged, which lowers the rated fuel economy, so most systems reset at every key cycle. The module carries your last choice across that reset.\u003c\/p\u003e\u003ch3\u003eDoes my Dodge RAM 1500 need the factory stop-start button for this to work?\u003c\/h3\u003e\u003cp\u003eYes. The module works with the factory stop-start system and its button. A vehicle built without stop-start has no setting for it to remember.\u003c\/p\u003e\u003ch3\u003eHow does it connect?\u003c\/h3\u003e\u003cp\u003eIt plugs in line with the factory connector named in the instructions, using factory-style plugs on both ends, so nothing is cut or spliced.\u003c\/p\u003e\u003ch3\u003eWhy does my Dodge RAM 1500 sometimes not auto-stop even when the system is on?\u003c\/h3\u003e\u003cp\u003eThe factory logic checks battery charge, engine temperature, climate load and other inputs. If any are outside range it keeps the engine running. The module does not affect those checks.\u003c\/p\u003e\u003ch3\u003eDoes it change how the battery is charged?\u003c\/h3\u003e\u003cp\u003eNo. Charging is still managed by the vehicle. Stop-start vehicles normally use an AGM or EFB battery built for frequent restarts; replace it with the same type when it wears out.\u003c\/p\u003e\u003ch2\u003eShipping, returns and warranty\u003c\/h2\u003e\u003cp\u003eStandard shipping inside the lower 48 states costs nothing; allow 1–2 business days of handling plus 3–4 in transit. Returns need approval first and must be requested within 45 days. Approved returns are subject to a 20% restocking fee, with return shipping paid by the customer. A 3-year limited warranty applies. Email support@automotivebypass.com (Mon–Fri, 9–5 PST) with your VIN if you want a fitment check.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493822771572,"sku":"RC-ASSE-64-01","price":109.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/2025-2026_Dodge_RAM_1500_4-Wheel_Drive_Auto_Start-Stop_Eliminators_1.jpg?v=1793348360","url":"https:\/\/automotivebypass.com\/products\/auto-start-stop-eliminator-2025-2026-dodge-ram-1500-4wd-auto-start-stop-eliminator","provider":"Automotivebypass","version":"1.0","type":"link"}