{"product_id":"tpms-sensor-eliminators-chevrolet-camaro-2010-2016-tpms-sensor-emulator","title":"Chevrolet Camaro 2010-2016 TPMS Sensor Emulator","description":"\u003cp\u003eThis module is for the 2010–2016 Chevrolet Camaro. It emulates the factory TPMS sensors, so a set of wheels without sensors does not trigger the low-tire or system-fault warning on the dash. It does not measure air pressure. Once it is in use, checking pressures with a gauge is your job, not the dashboard's.\u003c\/p\u003e\u003ch2\u003eCovered applications\u003c\/h2\u003e\u003cp\u003eEach row below is listed as a 100% fitment match:\u003c\/p\u003e\u003cul\u003e\u003cli\u003eChevrolet Camaro: 2010–2016\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eTPMS hardware can change within a model run (receiver version, sensor type), so match the exact model and year rather than the nameplate alone. Setup steps for your vehicle are in the included instructions.\u003c\/p\u003e\u003ch2\u003eWhy the warning comes on\u003c\/h2\u003e\u003cp\u003eThese vehicles use direct TPMS: a battery-powered sensor in each wheel sends pressure readings by radio, and a receiver in the vehicle matches each sensor by its ID. If a sensor goes quiet (dead battery, damaged sensor, or wheels without sensors), the system sets a fault. Federal standard FMVSS No. 138 requires this kind of warning on light vehicles built from September 1, 2007: a steady telltale when a tire is 25% or more below the placard pressure, and a malfunction indication that flashes for about a minute and then stays on when the system cannot work properly.\u003c\/p\u003e\u003ch2\u003eResponsible use\u003c\/h2\u003e\u003cp\u003eA TPMS emulator removes your low-pressure warning, so manual checks have to take its place: cold pressure readings from the placard, a monthly check at minimum, and a look at tread and sidewalls. Inspection and road-use rules for TPMS vary by state, and federal law limits what shops may disable. Confirm the rules for your situation before use.\u003c\/p\u003e\u003ch2\u003eChecking pressure the right way\u003c\/h2\u003e\u003cp\u003eWithout TPMS warnings, a monthly routine does the job: tires cold, gauge on each valve, compare with the door-jamb placard, top up as needed, and look over the tread and sidewalls. Larger off-road or winter tires may call for different pressures than the factory placard; follow the tire maker's guidance in that case.\u003c\/p\u003e\u003ch2\u003eWhere it fits in\u003c\/h2\u003e\u003cp\u003eMost buyers have wheels without sensors that they use part of the year, such as a winter set, a track set or a show set. The emulator keeps the dash clear while those wheels are on. When the original sensor-equipped wheels go back on, the factory system can be returned to normal operation following the instructions.\u003c\/p\u003e\u003ch2\u003eWhen the original wheels go back on\u003c\/h2\u003e\u003cp\u003eWhen you go back to the original sensor-equipped wheels, remove or disconnect the emulator as the instructions describe and let the vehicle recognize its sensors again. If the original sensors were rotated or replaced, the vehicle may need its normal TPMS relearn. Store the sensor wheels indoors and keep the valve caps on to keep moisture out of the valve stems.\u003c\/p\u003e\u003ch2\u003eDiagnosis first\u003c\/h2\u003e\u003cp\u003eIf the TPMS light remains on after setup, confirm the part matches your exact year and model, then follow the setup steps in the instructions again. A warning that persists can also point to a receiver or body-module fault, damaged wiring, or a different TPMS configuration than the one listed. The emulator cannot repair those, so a scan of the vehicle for stored codes is the next step.\u003c\/p\u003e\u003ch2\u003eWhat it does and does not do\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSupplies the TPMS signals the listed vehicle expects so the warning stays off on wheels without sensors.\u003c\/li\u003e\n\u003cli\u003eDoes not read, store or display real tire pressures.\u003c\/li\u003e\n\u003cli\u003eDoes not repair a faulty receiver, body module or wiring.\u003c\/li\u003e\n\u003cli\u003eDoes not replace pressure checks with a gauge or tire inspections.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eConfirm these points\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eYour model and year match a row above (2010–2016 Chevrolet Camaro).\u003c\/li\u003e\n\u003cli\u003eThe TPMS system works normally on your original sensor-equipped wheels.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket TPMS receiver or display has been added.\u003c\/li\u003e\n\u003cli\u003eYou have a tire gauge and will check pressures manually.\u003c\/li\u003e\n\u003cli\u003eUnsure? Email your VIN to support@automotivebypass.com.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment table\u003c\/h2\u003e\u003cp\u003eOne row per model year, from the fitment data for this SKU:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2010\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCamaro\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2011\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCamaro\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2012\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCamaro\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2013\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCamaro\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2014\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCamaro\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2015\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCamaro\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2016\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCamaro\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eIf the light stays on\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eLight flashes then stays on:\u003c\/strong\u003e The system still sees a malfunction. Re-check the fitment row and repeat the setup steps.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eLight was already on with the original wheels:\u003c\/strong\u003e The fault is in the vehicle (receiver, module or wiring) and needs repair first.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eLight returns after a wheel swap:\u003c\/strong\u003e Follow the instructions for switching between wheel sets; the original sensors may need the vehicle's normal relearn.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDifferent behavior from the description:\u003c\/strong\u003e Your vehicle may have a different TPMS configuration; contact support with the VIN.\u003c\/p\u003e\u003ch2\u003eWhat FMVSS No. 138 requires\u003c\/h2\u003e\u003cp\u003eFMVSS No. 138 came out of the TREAD Act of 2000. Phase-in started in October 2005, and all new US light vehicles up to 10,000 lb GVWR built from September 1, 2007 must have TPMS. The rule sets a low-pressure warning at 25% below the placard pressure, within 20 minutes of driving, and a separate malfunction signal: about a minute of flashing at start-up followed by a steady light. A missing sensor signal counts as a malfunction.\u003c\/p\u003e\u003ch2\u003eWhen the sensor wheels go back on (GM)\u003c\/h2\u003e\u003cp\u003eWhen the original sensor wheels go back on, GM owner's manuals describe a sensor matching process. With the parking brake set and the ignition on (engine off), hold the key fob LOCK and UNLOCK buttons together for about five seconds, or use the Driver Information Center menu; the horn sounds twice and TIRE LEARNING ACTIVE appears. Then activate each sensor with a TPMS relearn tool held against the sidewall near the valve stem, in order: driver front, passenger front, passenger rear, driver rear. A chirp confirms each one. You have two minutes for the first wheel and five minutes for all four. Finish by setting all tires to the placard pressure.\u003c\/p\u003e\u003ch2\u003ePreparation\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStart from a fault-free TPMS on the sensor wheels.\u003c\/li\u003e\n\u003cli\u003eRead your model's instructions.\u003c\/li\u003e\n\u003cli\u003eSet pressures cold to the placard figure.\u003c\/li\u003e\n\u003cli\u003eStore the sensor wheels indoors.\u003c\/li\u003e\n\u003cli\u003eComplete the setup as described.\u003c\/li\u003e\n\u003cli\u003eRestart and look at the TPMS light.\u003c\/li\u003e\n\u003cli\u003ePlan regular gauge checks from now on.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eTerms used on this page\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eMalfunction indicator:\u003c\/strong\u003e The TPMS light flashing at start-up and then staying on, signalling a system fault.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eTPMS:\u003c\/strong\u003e Tire pressure monitoring system.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDirect TPMS:\u003c\/strong\u003e A system with a pressure sensor in each wheel.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRelearn:\u003c\/strong\u003e The procedure that teaches the vehicle the IDs of its wheel sensors.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePlacard pressure:\u003c\/strong\u003e The recommended cold inflation pressure on the driver-side door-jamb label.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFMVSS No. 138:\u003c\/strong\u003e The federal safety standard that requires TPMS on new US light vehicles.\u003c\/p\u003e\u003ch2\u003eDirect and indirect TPMS\u003c\/h2\u003e\u003cp\u003eIndirect TPMS works out pressure from wheel speed through the ABS sensors. Direct TPMS, used on the Chevrolet Camaro, has a sensor with its own battery inside each wheel and reports measured pressure by radio. The sensor battery is sealed in, so a sensor is replaced when its battery runs down. Remove the sensors and a direct system reports a malfunction.\u003c\/p\u003e\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\u003ch3\u003eCan I go back to the original sensors?\u003c\/h3\u003e\u003cp\u003eYes. Remove the emulator, refit the sensor-equipped wheels and follow the vehicle's normal TPMS procedure.\u003c\/p\u003e\u003ch3\u003eDoes it measure tire pressure?\u003c\/h3\u003e\u003cp\u003eNo. It supplies the signals the system expects. Check pressures with a gauge.\u003c\/p\u003e\u003ch3\u003eWhich Chevrolet Camaro years does this TPMS emulator fit?\u003c\/h3\u003e\u003cp\u003eThe fitment table lists Chevrolet Camaro 2010–2016. Match your exact model and year before ordering.\u003c\/p\u003e\u003ch3\u003eWhy does my TPMS light flash and then stay on?\u003c\/h3\u003e\u003cp\u003eUnder FMVSS No. 138, a light that flashes for about a minute and then stays on indicates a system malfunction, such as missing sensor signals, rather than low pressure.\u003c\/p\u003e\u003ch3\u003eWill it fix a TPMS receiver or module fault?\u003c\/h3\u003e\u003cp\u003eNo. Receiver, wiring and module faults need their own diagnosis and repair.\u003c\/p\u003e\u003ch3\u003eWhy is TPMS required on US vehicles?\u003c\/h3\u003e\u003cp\u003eThe TREAD Act of 2000 directed NHTSA to require tire-pressure warnings, which led to FMVSS No. 138. All new US light vehicles built from September 1, 2007 must have it.\u003c\/p\u003e\u003ch3\u003eWill it work on a vehicle that is not listed?\u003c\/h3\u003e\u003cp\u003eDo not assume it will. TPMS receivers and sensor setups vary by model and year, so match the fitment rows or send the VIN to support.\u003c\/p\u003e\u003ch3\u003eDo I still need to check tire pressure?\u003c\/h3\u003e\u003cp\u003eYes. Check all tires cold at least once a month with a gauge, using the pressures on the driver-side door-jamb placard.\u003c\/p\u003e\u003ch3\u003eCan a tire shop work on the vehicle with the emulator installed?\u003c\/h3\u003e\u003cp\u003eTell the shop it is installed. Federal law restricts repair businesses from knowingly making TPMS inoperative, so some shops may ask you to remove it first.\u003c\/p\u003e\u003ch3\u003eIs it legal to use on the road?\u003c\/h3\u003e\u003cp\u003eTPMS is required equipment on new US light vehicles, and rules for owners and inspections vary by state. Check what applies before road use.\u003c\/p\u003e\u003ch2\u003eShipping, returns and warranty\u003c\/h2\u003e\u003cp\u003eStandard shipping inside the lower 48 states costs nothing; allow 1–2 business days of handling plus 3–4 in transit. Returns need approval first and must be requested within 45 days. Approved returns are subject to a 20% restocking fee, with return shipping paid by the customer. A 3-year limited warranty applies. Email support@automotivebypass.com (Mon–Fri, 9–5 PST) with your VIN if you want a fitment check.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493790331252,"sku":"TPMS-MOD-02-02","price":119.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/TPMS-MOD-02-02-1.jpg?v=1793092519","url":"https:\/\/automotivebypass.com\/products\/tpms-sensor-eliminators-chevrolet-camaro-2010-2016-tpms-sensor-emulator","provider":"Automotivebypass","version":"1.0","type":"link"}