{"product_id":"tpms-sensor-eliminators-chevrolet-cruze-2011-2016-tpms-sensor-emulator","title":"Chevrolet Cruze \/ Cruze Limited 2011-2016 TPMS Sensor Emulator","description":"\u003cp\u003eFor the 2011–2016 Chevrolet Cruze and 2016 Chevrolet Cruze Limited: an emulator that supplies the TPMS signals the vehicle is looking for. Typical use is a second set of wheels that has no sensors, where the factory system would otherwise keep its warning lit. It does not measure air pressure. Once it is in use, checking pressures with a gauge is your job, not the dashboard's.\u003c\/p\u003e\u003ch2\u003eFitment\u003c\/h2\u003e\u003cp\u003eListed applications (all 100% fitment match):\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eChevrolet Cruze: 2011–2016\u003c\/li\u003e\n\u003cli\u003eChevrolet Cruze Limited: 2016\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eUse the model and year rows above as the deciding check. Different receivers or sensor configurations within the same nameplate are why fitment is listed this narrowly.\u003c\/p\u003e\u003ch2\u003eThe factory TPMS in brief\u003c\/h2\u003e\u003cp\u003eEvery wheel on the Chevrolet Cruze and Chevrolet Cruze Limited normally carries a pressure sensor with its own ID, and the vehicle only listens for the IDs it has learned. Mount wheels without sensors and those IDs stop transmitting, so the system reports a fault. Under FMVSS No. 138, that fault shows as a TPMS light that flashes for roughly a minute at start-up and then stays lit, repeating on every start until the system sees its sensors again.\u003c\/p\u003e\u003ch2\u003eSeasonal wheel swaps\u003c\/h2\u003e\u003cp\u003eWhen you go back to the original sensor-equipped wheels, remove or disconnect the emulator as the instructions describe and let the vehicle recognize its sensors again. If the original sensors were rotated or replaced, the vehicle may need its normal TPMS relearn. Store the sensor wheels indoors and keep the valve caps on to keep moisture out of the valve stems.\u003c\/p\u003e\u003ch2\u003eTroubleshooting\u003c\/h2\u003e\u003cp\u003eIf the TPMS light remains on after setup, confirm the part matches your exact year and model, then follow the setup steps in the instructions again. A warning that persists can also point to a receiver or body-module fault, damaged wiring, or a different TPMS configuration than the one listed. The emulator cannot repair those, so a scan of the vehicle for stored codes is the next step.\u003c\/p\u003e\u003ch2\u003eChecking pressure the right way\u003c\/h2\u003e\u003cp\u003eWithout TPMS warnings, a monthly routine does the job: tires cold, gauge on each valve, compare with the door-jamb placard, top up as needed, and look over the tread and sidewalls. Larger off-road or winter tires may call for different pressures than the factory placard; follow the tire maker's guidance in that case.\u003c\/p\u003e\u003ch2\u003eResponsible use\u003c\/h2\u003e\u003cp\u003eA TPMS emulator removes your low-pressure warning, so manual checks have to take its place: cold pressure readings from the placard, a monthly check at minimum, and a look at tread and sidewalls. Inspection and road-use rules for TPMS vary by state, and federal law limits what shops may disable. Confirm the rules for your situation before use.\u003c\/p\u003e\u003ch2\u003eTypical uses\u003c\/h2\u003e\u003cp\u003eIt is aimed at vehicles that spend time on wheels without sensors: off-road builds, track days, winter tires on steel wheels, or show vehicles. On each of those, a permanent TPMS light hides any other warning that might appear in the same spot, which is the main reason owners want it gone.\u003c\/p\u003e\u003ch2\u003eWhat it does and does not do\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSupplies the TPMS signals the listed vehicle expects so the warning stays off on wheels without sensors.\u003c\/li\u003e\n\u003cli\u003eDoes not read, store or display real tire pressures.\u003c\/li\u003e\n\u003cli\u003eDoes not repair a faulty receiver, body module or wiring.\u003c\/li\u003e\n\u003cli\u003eDoes not replace pressure checks with a gauge or tire inspections.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCheck before you order\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eYour model and year match a row above (2011–2016 Chevrolet Cruze and 2016 Chevrolet Cruze Limited).\u003c\/li\u003e\n\u003cli\u003eThe TPMS system works normally on your original sensor-equipped wheels.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket TPMS receiver or display has been added.\u003c\/li\u003e\n\u003cli\u003eYou have a tire gauge and will check pressures manually.\u003c\/li\u003e\n\u003cli\u003eUnsure? Email your VIN to support@automotivebypass.com.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eEvery listed year\u003c\/h2\u003e\u003cp\u003eEach model year in the fitment data, listed separately:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2011\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCruze\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2012\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCruze\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2013\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCruze\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2014\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCruze\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2015\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCruze\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2016\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCruze\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2016\u003c\/td\u003e\n\u003ctd\u003eChevrolet\u003c\/td\u003e\n\u003ctd\u003eCruze Limited\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eWhen the sensor wheels go back on (GM)\u003c\/h2\u003e\u003cp\u003eWhen the original sensor wheels go back on, GM owner's manuals describe a sensor matching process. With the parking brake set and the ignition on (engine off), hold the key fob LOCK and UNLOCK buttons together for about five seconds, or use the Driver Information Center menu; the horn sounds twice and TIRE LEARNING ACTIVE appears. Then activate each sensor with a TPMS relearn tool held against the sidewall near the valve stem, in order: driver front, passenger front, passenger rear, driver rear. A chirp confirms each one. You have two minutes for the first wheel and five minutes for all four. Finish by setting all tires to the placard pressure.\u003c\/p\u003e\u003ch2\u003eGlossary\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eFMVSS No. 138:\u003c\/strong\u003e The federal safety standard that requires TPMS on new US light vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePlacard pressure:\u003c\/strong\u003e The recommended cold inflation pressure on the driver-side door-jamb label.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMalfunction indicator:\u003c\/strong\u003e The TPMS light flashing at start-up and then staying on, signalling a system fault.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRelearn:\u003c\/strong\u003e The procedure that teaches the vehicle the IDs of its wheel sensors.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDirect TPMS:\u003c\/strong\u003e A system with a pressure sensor in each wheel.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eTPMS:\u003c\/strong\u003e Tire pressure monitoring system.\u003c\/p\u003e\u003ch2\u003eSetup prep checklist\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWorking TPMS on the original wheels.\u003c\/li\u003e\n\u003cli\u003eInstructions for your exact vehicle at hand.\u003c\/li\u003e\n\u003cli\u003eTire gauge ready; pressures set cold to the placard.\u003c\/li\u003e\n\u003cli\u003eOriginal wheels stored safely, caps on.\u003c\/li\u003e\n\u003cli\u003eSetup completed step by step.\u003c\/li\u003e\n\u003cli\u003eDash checked after a restart.\u003c\/li\u003e\n\u003cli\u003eMonthly pressure check scheduled.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAfter-setup checks\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eMalfunction light persists:\u003c\/strong\u003e Confirm year and model against the table and redo setup.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFault present before installation:\u003c\/strong\u003e Have the receiver, module and wiring diagnosed.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWarning after refitting sensor wheels:\u003c\/strong\u003e Run the standard TPMS relearn for your vehicle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eUnexpected behavior:\u003c\/strong\u003e Send the VIN to support so the configuration can be checked.\u003c\/p\u003e\u003ch2\u003eWhat FMVSS No. 138 requires\u003c\/h2\u003e\u003cp\u003eFMVSS No. 138 came out of the TREAD Act of 2000. Phase-in started in October 2005, and all new US light vehicles up to 10,000 lb GVWR built from September 1, 2007 must have TPMS. The rule sets a low-pressure warning at 25% below the placard pressure, within 20 minutes of driving, and a separate malfunction signal: about a minute of flashing at start-up followed by a steady light. A missing sensor signal counts as a malfunction.\u003c\/p\u003e\u003ch2\u003eHow these vehicles monitor pressure\u003c\/h2\u003e\u003cp\u003eThere are two ways to monitor tire pressure. Indirect systems use the ABS wheel-speed sensors and look for a tire turning faster because it is underinflated. Direct systems, like the one on the Chevrolet Cruze and Chevrolet Cruze Limited, put a battery-powered sensor in each wheel, usually on the valve stem, and transmit actual pressure. Because a direct system expects to hear each sensor, wheels without sensors cause a fault, which is the situation the emulator addresses.\u003c\/p\u003e\u003ch2\u003eFAQ\u003c\/h2\u003e\u003ch3\u003eWhich Chevrolet Cruze and Chevrolet Cruze Limited years does this TPMS emulator fit?\u003c\/h3\u003e\u003cp\u003eThe fitment table lists Chevrolet Cruze 2011–2016; Chevrolet Cruze Limited 2016. Match your exact model and year before ordering.\u003c\/p\u003e\u003ch3\u003eWhy does my TPMS light flash and then stay on?\u003c\/h3\u003e\u003cp\u003eUnder FMVSS No. 138, a light that flashes for about a minute and then stays on indicates a system malfunction, such as missing sensor signals, rather than low pressure.\u003c\/p\u003e\u003ch3\u003eIs it legal to use on the road?\u003c\/h3\u003e\u003cp\u003eTPMS is required equipment on new US light vehicles, and rules for owners and inspections vary by state. Check what applies before road use.\u003c\/p\u003e\u003ch3\u003eCan I go back to the original sensors?\u003c\/h3\u003e\u003cp\u003eYes. Remove the emulator, refit the sensor-equipped wheels and follow the vehicle's normal TPMS procedure.\u003c\/p\u003e\u003ch3\u003eDoes it measure tire pressure?\u003c\/h3\u003e\u003cp\u003eNo. It supplies the signals the system expects. Check pressures with a gauge.\u003c\/p\u003e\u003ch3\u003eWill it work on a vehicle that is not listed?\u003c\/h3\u003e\u003cp\u003eDo not assume it will. TPMS receivers and sensor setups vary by model and year, so match the fitment rows or send the VIN to support.\u003c\/p\u003e\u003ch3\u003eDo I still need to check tire pressure?\u003c\/h3\u003e\u003cp\u003eYes. Check all tires cold at least once a month with a gauge, using the pressures on the driver-side door-jamb placard.\u003c\/p\u003e\u003ch3\u003eWill it fix a TPMS receiver or module fault?\u003c\/h3\u003e\u003cp\u003eNo. Receiver, wiring and module faults need their own diagnosis and repair.\u003c\/p\u003e\u003ch3\u003eCan a tire shop work on the vehicle with the emulator installed?\u003c\/h3\u003e\u003cp\u003eTell the shop it is installed. Federal law restricts repair businesses from knowingly making TPMS inoperative, so some shops may ask you to remove it first.\u003c\/p\u003e\u003ch3\u003eWhy is TPMS required on US vehicles?\u003c\/h3\u003e\u003cp\u003eThe TREAD Act of 2000 directed NHTSA to require tire-pressure warnings, which led to FMVSS No. 138. All new US light vehicles built from September 1, 2007 must have it.\u003c\/p\u003e\u003ch2\u003eWarranty and returns\u003c\/h2\u003e\u003cp\u003eFree standard shipping covers the contiguous US, with dispatch in 1–2 business days and 3–4 days on the road after that. You have 45 days to request a return (pre-approval required, 20% restocking fee, buyer-paid return shipping). The module is backed by a 3-year limited warranty. For order or fitment questions, write to support@automotivebypass.com between 9 and 5 Pacific, Monday through Friday.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493790429556,"sku":"TPMS-MOD-02-05","price":119.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/TPMS-MOD-02-05-1.jpg?v=1793092551","url":"https:\/\/automotivebypass.com\/products\/tpms-sensor-eliminators-chevrolet-cruze-2011-2016-tpms-sensor-emulator","provider":"Automotivebypass","version":"1.0","type":"link"}