{"product_id":"tpms-sensor-eliminators-gmc-terrain-2010-2016-tpms-sensor-emulator","title":"GMC Terrain 2010-2016 TPMS Sensor Emulator","description":"\u003cp\u003eThe GMC Terrain expects to hear from a sensor in each wheel. When the wheels on the vehicle have no sensors, the dash shows a TPMS fault. This emulator for the 2010–2016 GMC Terrain provides those signals so the warning stays off. It does not measure air pressure. Once it is in use, checking pressures with a gauge is your job, not the dashboard's.\u003c\/p\u003e\u003ch2\u003eCovered applications\u003c\/h2\u003e\u003cp\u003eListed applications (all 100% fitment match):\u003c\/p\u003e\u003cul\u003e\u003cli\u003eGMC Terrain: 2010–2016\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eTPMS hardware can change within a model run (receiver version, sensor type), so match the exact model and year rather than the nameplate alone. Setup steps for your vehicle are in the included instructions.\u003c\/p\u003e\u003ch2\u003eHow factory TPMS works on these vehicles\u003c\/h2\u003e\u003cp\u003eThese vehicles use direct TPMS: a battery-powered sensor in each wheel sends pressure readings by radio, and a receiver in the vehicle matches each sensor by its ID. If a sensor goes quiet (dead battery, damaged sensor, or wheels without sensors), the system sets a fault. Federal standard FMVSS No. 138 requires this kind of warning on light vehicles built from September 1, 2007: a steady telltale when a tire is 25% or more below the placard pressure, and a malfunction indication that flashes for about a minute and then stays on when the system cannot work properly.\u003c\/p\u003e\u003ch2\u003eTypical uses\u003c\/h2\u003e\u003cp\u003eThe usual situation is a second wheel set: dedicated winter wheels, track wheels or off-road wheels that were never fitted with sensors. Buying and programming a second set of sensors costs money and time, and without them the TPMS light stays on all season. An emulator covers that set while the original wheels and sensors sit in storage.\u003c\/p\u003e\u003ch2\u003eDiagnosis first\u003c\/h2\u003e\u003cp\u003eA light that will not clear usually means a mismatch: a different year or receiver version than the listing, or a setup step that did not complete. Re-check the fitment rows and instructions. If they match, scan for codes, because a receiver or module fault will keep the light on regardless of what is installed.\u003c\/p\u003e\u003ch2\u003eSeasonal wheel swaps\u003c\/h2\u003e\u003cp\u003eWhen you go back to the original sensor-equipped wheels, remove or disconnect the emulator as the instructions describe and let the vehicle recognize its sensors again. If the original sensors were rotated or replaced, the vehicle may need its normal TPMS relearn. Store the sensor wheels indoors and keep the valve caps on to keep moisture out of the valve stems.\u003c\/p\u003e\u003ch2\u003eResponsible use\u003c\/h2\u003e\u003cp\u003eA TPMS emulator removes your low-pressure warning, so manual checks have to take its place: cold pressure readings from the placard, a monthly check at minimum, and a look at tread and sidewalls. Inspection and road-use rules for TPMS vary by state, and federal law limits what shops may disable. Confirm the rules for your situation before use.\u003c\/p\u003e\u003ch2\u003eUsing the placard pressure\u003c\/h2\u003e\u003cp\u003eUse the cold inflation pressure printed on the tire placard on the driver-side door jamb, not the maximum figure molded into the tire sidewall. \"Cold\" means the vehicle has been parked for about three hours or driven only a short distance. Check every tire including the spare, add air in small steps, and recheck. Doing this monthly covers most of what the TPMS warning would have told you.\u003c\/p\u003e\u003ch2\u003eScope\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSupplies the TPMS signals the listed vehicle expects so the warning stays off on wheels without sensors.\u003c\/li\u003e\n\u003cli\u003eDoes not read, store or display real tire pressures.\u003c\/li\u003e\n\u003cli\u003eDoes not repair a faulty receiver, body module or wiring.\u003c\/li\u003e\n\u003cli\u003eDoes not replace pressure checks with a gauge or tire inspections.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment check\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eYour model and year match a row above (2010–2016 GMC Terrain).\u003c\/li\u003e\n\u003cli\u003eThe TPMS system works normally on your original sensor-equipped wheels.\u003c\/li\u003e\n\u003cli\u003eNo aftermarket TPMS receiver or display has been added.\u003c\/li\u003e\n\u003cli\u003eYou have a tire gauge and will check pressures manually.\u003c\/li\u003e\n\u003cli\u003eUnsure? Email your VIN to support@automotivebypass.com.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eEvery listed year\u003c\/h2\u003e\u003cp\u003eOne row per model year, from the fitment data for this SKU:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eYear\u003c\/th\u003e\n\u003cth\u003eMake\u003c\/th\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eEngine \/ trim\u003c\/th\u003e\n\u003cth\u003eListing note\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2010\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eTerrain\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2011\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eTerrain\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2012\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eTerrain\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2013\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eTerrain\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2014\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eTerrain\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2015\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eTerrain\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e2016\u003c\/td\u003e\n\u003ctd\u003eGMC\u003c\/td\u003e\n\u003ctd\u003eTerrain\u003c\/td\u003e\n\u003ctd\u003eAll\u003c\/td\u003e\n\u003ctd\u003e100% Fitment Match | OEM-Grade Quality | Plug \u0026amp; Play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch2\u003eWhat FMVSS No. 138 requires\u003c\/h2\u003e\u003cp\u003eThe TPMS requirement is federal standard FMVSS No. 138, adopted under the TREAD Act of 2000 and fully in force for light vehicles built from September 1, 2007. It requires a warning when any tire is at least 25% under the recommended cold pressure, delivered within 20 minutes of driving, and a malfunction indication (flashing for roughly 60–90 seconds, then steady) when the system cannot do its job, including when sensors are absent.\u003c\/p\u003e\u003ch2\u003eDirect and indirect TPMS\u003c\/h2\u003e\u003cp\u003eThe GMC Terrain uses direct TPMS: sensors in the wheels, normally attached to the valve stems, each with a sealed battery and a unique ID. Indirect systems, used by some other makers, rely on ABS wheel-speed data instead. Direct systems are the ones that complain when sensors are missing, which is why an emulator is needed on sensorless wheels.\u003c\/p\u003e\u003ch2\u003eSetup prep checklist\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStart from a fault-free TPMS on the sensor wheels.\u003c\/li\u003e\n\u003cli\u003eRead your model's instructions.\u003c\/li\u003e\n\u003cli\u003eSet pressures cold to the placard figure.\u003c\/li\u003e\n\u003cli\u003eStore the sensor wheels indoors.\u003c\/li\u003e\n\u003cli\u003eComplete the setup as described.\u003c\/li\u003e\n\u003cli\u003eRestart and look at the TPMS light.\u003c\/li\u003e\n\u003cli\u003ePlan regular gauge checks from now on.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eGlossary\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eMalfunction indicator:\u003c\/strong\u003e The TPMS light flashing at start-up and then staying on, signalling a system fault.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDirect TPMS:\u003c\/strong\u003e A system with a pressure sensor in each wheel.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePlacard pressure:\u003c\/strong\u003e The recommended cold inflation pressure on the driver-side door-jamb label.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eTPMS:\u003c\/strong\u003e Tire pressure monitoring system.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFMVSS No. 138:\u003c\/strong\u003e The federal safety standard that requires TPMS on new US light vehicles.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eRelearn:\u003c\/strong\u003e The procedure that teaches the vehicle the IDs of its wheel sensors.\u003c\/p\u003e\u003ch2\u003eAfter-setup checks\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eStill lit after setup:\u003c\/strong\u003e Check fitment and repeat the steps in order.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIt was lit before:\u003c\/strong\u003e Repair the existing TPMS fault first.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBack on original wheels and lit:\u003c\/strong\u003e Use the vehicle's normal relearn procedure.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNot sure what is happening:\u003c\/strong\u003e Email support with your VIN.\u003c\/p\u003e\u003ch2\u003eWhen the sensor wheels go back on (GM)\u003c\/h2\u003e\u003cp\u003eGM's documented relearn is quick once you have a TPMS tool. Set the parking brake, switch the ignition on without starting the engine and put the receiver in learn mode (LOCK plus UNLOCK on the fob for roughly five seconds, or the tire-pressure item in the DIC menu) until the horn chirps twice. Trigger the sensors in the order driver front, passenger front, passenger rear, driver rear; each answers with a chirp, and the last with two. The process stops if the first wheel takes more than two minutes or all four take more than five.\u003c\/p\u003e\u003ch2\u003eCommon questions\u003c\/h2\u003e\u003ch3\u003eWhy does my TPMS light flash and then stay on?\u003c\/h3\u003e\u003cp\u003eUnder FMVSS No. 138, a light that flashes for about a minute and then stays on indicates a system malfunction, such as missing sensor signals, rather than low pressure.\u003c\/p\u003e\u003ch3\u003eDoes it measure tire pressure?\u003c\/h3\u003e\u003cp\u003eNo. It supplies the signals the system expects. Check pressures with a gauge.\u003c\/p\u003e\u003ch3\u003eIs it legal to use on the road?\u003c\/h3\u003e\u003cp\u003eTPMS is required equipment on new US light vehicles, and rules for owners and inspections vary by state. Check what applies before road use.\u003c\/p\u003e\u003ch3\u003eWhich GMC Terrain years does this TPMS emulator fit?\u003c\/h3\u003e\u003cp\u003eThe fitment table lists GMC Terrain 2010–2016. Match your exact model and year before ordering.\u003c\/p\u003e\u003ch3\u003eWill it fix a TPMS receiver or module fault?\u003c\/h3\u003e\u003cp\u003eNo. Receiver, wiring and module faults need their own diagnosis and repair.\u003c\/p\u003e\u003ch3\u003eWhy is TPMS required on US vehicles?\u003c\/h3\u003e\u003cp\u003eThe TREAD Act of 2000 directed NHTSA to require tire-pressure warnings, which led to FMVSS No. 138. All new US light vehicles built from September 1, 2007 must have it.\u003c\/p\u003e\u003ch3\u003eCan a tire shop work on the vehicle with the emulator installed?\u003c\/h3\u003e\u003cp\u003eTell the shop it is installed. Federal law restricts repair businesses from knowingly making TPMS inoperative, so some shops may ask you to remove it first.\u003c\/p\u003e\u003ch3\u003eCan I go back to the original sensors?\u003c\/h3\u003e\u003cp\u003eYes. Remove the emulator, refit the sensor-equipped wheels and follow the vehicle's normal TPMS procedure.\u003c\/p\u003e\u003ch3\u003eWill it work on a vehicle that is not listed?\u003c\/h3\u003e\u003cp\u003eDo not assume it will. TPMS receivers and sensor setups vary by model and year, so match the fitment rows or send the VIN to support.\u003c\/p\u003e\u003ch3\u003eDo I still need to check tire pressure?\u003c\/h3\u003e\u003cp\u003eYes. Check all tires cold at least once a month with a gauge, using the pressures on the driver-side door-jamb placard.\u003c\/p\u003e\u003ch2\u003eWarranty and returns\u003c\/h2\u003e\u003cp\u003eWe ship free within the contiguous United States (1–2 business days to dispatch, roughly 3–4 business days in transit). If it turns out to be the wrong part, request a return authorization within 45 days; returns carry a 20% restocking fee and return postage is on the buyer. Coverage is a 3-year limited warranty. Questions go to support@automotivebypass.com, weekdays 9 a.m. to 5 p.m. PST.\u003c\/p\u003e","brand":"Automotivebypass","offers":[{"title":"Default Title","offer_id":56493789970804,"sku":"TPMS-MOD-01-07","price":119.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1030\/8439\/2820\/files\/TPMS-MOD-01-07-1.jpg?v=1793092477","url":"https:\/\/automotivebypass.com\/products\/tpms-sensor-eliminators-gmc-terrain-2010-2016-tpms-sensor-emulator","provider":"Automotivebypass","version":"1.0","type":"link"}