Chevrolet Caprice PPV 2011-2019 6.0L V8 AFM/DFM Disabler

Fits the 2011–2019 Chevrolet Caprice PPV. The module connects at the OBD-II port and keeps GM's cylinder deactivation from switching on, which means steady all-cylinder operation instead of repeated changes between full and partial mode. No tools, no wiring and no reflash of the engine computer. Unplug it and AFM works again as it did from the factory.

What it fits

The fitment table for this part (all rows marked 100% fitment match):

• 2011–2019 Chevrolet Caprice PPV: 6.0L V8

GM engine codes with AFM that line up with these years and displacements:

• L77 (6.0L, 2011–2017, VIN 8th digit "2")

An engine code that is not listed here does not automatically rule the vehicle out, but send us the VIN first so we can check.

What AFM does on these engines

On AFM V8 engines, the computer shuts off fuel and holds the valves closed on cylinders 1, 7, 6 and 4 when the load is light, so the engine runs as a V4. It does this through special collapsible lifters on those cylinders, fed by oil-pressure solenoids. When you ask for more power, the lifters lock again and all eight cylinders fire. GM describes this behavior in its service bulletin on AFM and DFM operation.

Practical notes

Because it occupies the OBD-II port, unplug the module before connecting a scan tool, an insurance logger or an emissions-test probe, then plug it back in afterwards. Make sure it sits clear of your left knee and the pedals, and that the housing is fully seated in the port.

What to expect on the road

Drive at a steady cruise on a light throttle, where AFM used to switch modes. The engine should now stay on all cylinders, so the subtle shudder, drone or hesitation that came with each change should be gone. If your dash shows instant fuel economy, expect the light-cruise numbers to read a little lower than before, since that is exactly where cylinder deactivation saved fuel.

Why owners disable it

The usual complaints are a drone or shudder in reduced-cylinder mode, a slight hesitation when the engine switches back, and a general wish to keep the valvetrain doing the same thing all the time. With the module installed, the engine stays in full-cylinder mode, so those transitions stop. Expect light-load fuel economy to be closer to an engine without AFM.

Plug-in module vs. a mechanical AFM delete

There are three common ways to stop cylinder deactivation on GM engines: a plug-in module like this one, a custom tune that turns AFM off in the engine computer, or a mechanical delete that replaces the AFM lifters and related hardware and then needs a tune to match. The module is the only one of the three that needs no tools and no engine-computer changes, and it is the only one you can undo by unplugging it. It does not replace failed lifters; if hardware is already damaged, the repair comes first.

Diagnose existing problems first

Scan for stored codes before you plug it in. Misfire codes on the deactivation cylinders, an AFM solenoid circuit code, or a lifter noise are signs of an existing problem that should be repaired first. The module is meant for a healthy engine where you simply do not want cylinder deactivation.

Maintenance still matters

Oil level and quality are worth watching on any AFM engine, because the deactivation hardware is hydraulic. Check the dipstick at fuel stops on high-mileage engines, follow GM's specified oil grade, and address oil-pressure warnings immediately. None of that changes with the module installed.

Fitment check

• Your model year, model and engine match a row in the table (2011–2019 Chevrolet Caprice PPV).
• Look up the engine RPO code. Older GM vehicles print it on the Service Parts Identification sticker, often in the glovebox; 2018 and newer GM models carry it in a QR code on the driver-side B-pillar label. You can also read the 8th digit of the VIN, which is the engine code.
• No check-engine light is on, and oil level and pressure are normal.
• If the vehicle has an engine swap, an aftermarket tune or a replacement engine computer, contact support first.
• Questions: support@automotivebypass.com with your VIN.

Warranty and returns

We ship free within the contiguous United States (1–2 business days to dispatch, roughly 3–4 business days in transit). If it turns out to be the wrong part, request a return authorization within 45 days; returns carry a 20% restocking fee and return postage is on the buyer. Coverage is a 3-year limited warranty. Questions go to support@automotivebypass.com, weekdays 9 a.m. to 5 p.m. PST.