2024-2026 Chevrolet Traverse Auto Start Stop Eliminator | Plug & Play

Fits the 2024–2026 Chevrolet Traverse. The plug-and-play memory harness remembers the position of the stop-start button between drives, so the engine no longer shuts off at the first red light after every restart unless you want it to. It plugs in line with the factory connector named in the instructions, using factory-style plugs on both ends, so nothing is cut or spliced.

Nothing is reprogrammed in the engine computer. The module only stands in for the button press you would otherwise make after every start, and it comes out without leaving a trace.

Covered model years

Every row below is listed as a 100% fitment match for this part:

• Chevrolet Traverse: 2024–2026

For reference, the Chevrolet Traverse in these years is a three-row midsize crossover offered with 3.6L V6 engines, with a 2.0L turbo four-cylinder offered on 2018-2019 models. The listing is written around the third-generation (2024-up) Traverse. Trim levels are not split out in the table, so confirm that your vehicle has the stop-start button before ordering.

How Auto Stop/Start behaves from the factory

Each start of the Chevrolet Traverse begins with Auto Stop/Start enabled. The switch on the dash can disable it, but only until the key is cycled. This module records the switch position and repeats it after the restart, which is the entire job it does.

Keep the battery healthy

The module draws its power from the vehicle and does not change charging behavior. If your Chevrolet Traverse sits for long periods, the same rules apply as without it: a maintainer helps, and a battery that tests weak should be replaced with the type specified for stop-start vehicles (usually AGM or EFB).

If stop-start is not engaging

The factory system will skip an auto stop for many reasons: battery charge below its threshold, cold coolant, high climate-control load, a steep grade, the hood or driver door open, or a 4WD or tow mode on vehicles that have them. Those checks stay in control after this module is installed. It does not force stops and it does not bypass any of those safety inputs.

What changes after installation

• Fully reversible: unplug it and the vehicle returns to factory behavior.
• Keeps the original switch fully functional.
• No tune, no reflash, no change to horsepower or shift points.
• Stores the stop-start choice you made last and repeats it at the next start.

If something does not look right

A dead or weak battery, a charging problem or an unrelated module fault will change how Auto Stop/Start behaves with or without this part installed. Scan the vehicle for stored codes, test the battery and confirm the system works normally with the factory button before installation. That baseline makes any later issue easy to pin down.

Where owners notice the difference

Some owners only want stop-start off in certain seasons or on certain trips, such as towing a trailer or crawling through summer traffic with the A/C working hard. Because the module remembers whatever you chose last, it works both ways: leave the system off for a week, then switch it back on with the factory button and it stays on.

Connecting it

It plugs in line with the factory connector named in the instructions, using factory-style plugs on both ends, so nothing is cut or spliced. Work with the ignition off. Seat each connector until its lock engages, then secure the module with the supplied ties or tape so it cannot rattle or touch pedals, steering parts or anything hot. Start the vehicle, press the stop-start button once, then restart to confirm the choice is held.

Quick fitment check

• Model year and model match a row in the table above (2024–2026 Chevrolet Traverse).
• Your Chevrolet Traverse has the factory stop-start button. Base trims or engines without stop-start have nothing for the module to remember.
• The connector at your install point matches the one in the product photos.
• The battery and charging system test good and no warning lights are on.
• No aftermarket remote start, alarm or gateway bypass is wired into the same circuit. If one is, email support before ordering.
• If you are unsure, send your VIN to support@automotivebypass.com and we will confirm fitment.

Ordering details

Standard shipping inside the lower 48 states costs nothing; allow 1–2 business days of handling plus 3–4 in transit. Returns need approval first and must be requested within 45 days. Approved returns are subject to a 20% restocking fee, with return shipping paid by the customer. A 3-year limited warranty applies. Email support@automotivebypass.com (Mon–Fri, 9–5 PST) with your VIN if you want a fitment check.